RFC3276 日本語訳

3276 Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line(SHDSL) Lines Processing. B. Ray, R. Abbi. May 2002. (Format: TXT=122991 bytes) (Obsoleted by RFC4319) (Status: PROPOSED STANDARD)
プログラムでの自動翻訳です。
英語原文

Network Working Group                                             B. Ray
Request for Comments: 3276                        PESA Switching Systems
Category: Standards Track                                        R. Abbi
                                                                 Alcatel
                                                                May 2002

コメントを求めるワーキンググループB.レイの要求をネットワークでつないでください: 3276年のペサ交換システムカテゴリ: 標準化過程R.Abbiアルカテル2002年5月

 Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation
         (HDSL2) and Single-Pair High-Speed Digital Subscriber
                           Line (SHDSL) Lines

高いビット伝送速度DSLのための管理オブジェクトの定義--第2世代(HDSL2)と単独の組の高速デジタル加入者線(SHDSL)線

Status of this Memo

このMemoの状態

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

このドキュメントは、インターネットコミュニティにインターネット標準化過程プロトコルを指定して、改良のために議論と提案を要求します。 このプロトコルの標準化状態と状態への「インターネット公式プロトコル標準」(STD1)の現行版を参照してください。 このメモの分配は無制限です。

Copyright Notice

版権情報

   Copyright (C) The Internet Society (2002).  All Rights Reserved.

Copyright(C)インターネット協会(2002)。 All rights reserved。

Abstract

要約

   This document defines a portion of the Management Information Base
   (MIB) module for use with network management protocols in the
   Internet community.  In particular, it describes objects used for
   managing High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair
   High-Speed Digital Subscriber Line (SHDSL) interfaces.

ネットワーク管理プロトコルがインターネットコミュニティにある状態で、このドキュメントは使用のためのManagement Information基地(MIB)のモジュールの部分を定義します。 特に、High Bit-レートDSLを管理するのに使用される物について説明します--第2世代(HDSL2)とSingle-組High-速度Digital Subscriber線(SHDSL)のインタフェース。

Table of Contents

目次

   1.   Introduction .............................................  2
   2.   The SNMP Network Management Framework ....................  2
   3.   Introduction .............................................  3
   3.1  Relationship of the HDSL2/SHDSL Line MIB to other MIBs ...  3
   3.2  IANA Considerations ......................................  5
   4.   Conventions used in the MIB ..............................  5
   4.1  Naming Conventions .......................................  5
   4.2  Textual Conventions ......................................  6
   4.3  Structure ................................................  7
   4.4  Counters, Interval Buckets and Thresholds ................ 10
   4.5  Profiles ................................................. 11
   4.6  Notifications ............................................ 12
   5.   Conformance and Compliance ............................... 14
   6.   Definitions .............................................. 14
   7.   Security Considerations .................................. 60

1. 序論… 2 2. SNMPネットワークマネージメント枠組み… 2 3. 序論… 3 3.1 他のMIBsへのHDSL2/SHDSL線MIBの関係… 3 3.2 IANA問題… 5 4. MIBで中古のコンベンション… 5 4.1 コンベンションを命名します… 5 4.2 原文のコンベンション… 6 4.3 構造… 7 4.4のカウンタ、間隔バケツ、および敷居… 10 4.5 輪郭を描きます。 11 4.6の通知… 12 5. 順応と承諾… 14 6. 定義… 14 7. セキュリティ問題… 60

Ray & Abbi                  Standards Track                     [Page 1]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[1ページ]。

   8.   Acknowledgments .......................................... 62
   9.   References ............................................... 63
   10.  Intellectual Property Notice ............................. 65
   11.  Authors' Addresses ....................................... 65
   12.  Full Copyright Statement ................................. 66

8. 承認… 62 9. 参照… 63 10. 知的所有権通知… 65 11. 作者のアドレス… 65 12. 完全な著作権宣言文… 66

1. Introduction

1. 序論

   This document defines a portion of the Management Information Base
   (MIB) module for use with network management protocols in the
   Internet community.  In particular, it describes objects used for
   managing High Bit-Rate DSL - 2nd generation (HDSL2) [18] and Single-
   Pair High-Speed Digital Subscriber Line (SHDSL) interfaces [19].

ネットワーク管理プロトコルがインターネットコミュニティにある状態で、このドキュメントは使用のためのManagement Information基地(MIB)のモジュールの部分を定義します。 特に、High Bit-レートDSLを管理するのに使用される物について説明します--2番目の世代(HDSL2)[18]とSingle組High-速度Digital Subscriber線(SHDSL)のインタフェース[19]。

2.  The SNMP Management Framework

2. SNMP管理枠組み

   The SNMP Management Framework presently consists of five major
   components:

SNMP Management Frameworkは現在、5個の主要コンポーネントから成ります:

   o  An overall architecture, described in RFC 2571 [1].

o RFC2571[1]で説明された総合的な構造。

   o  Mechanisms for describing and naming objects and events for the
      purpose of management.  The first version of this Structure of
      Management Information (SMI) is called SMIv1 and is described in
      STD 16, RFC 1155 [2], STD 16, RFC 1212 [3], and RFC 1215 [4].  The
      second version, called SMIv2, is described in STD 58, RFC 2578
      [5], RFC 2579 [6], and RFC 2580 [7].

o 物を説明して、命名するためのメカニズムと管理の目的のための出来事。 Management情報(SMI)のこのStructureの最初のバージョンは、SMIv1と呼ばれて、STD16、RFC1155[2]、STD16、RFC1212[3]、およびRFC1215[4]で説明されます。 SMIv2と呼ばれる第2バージョンはSTD58、RFC2578[5]、RFC2579[6]、およびRFC2580[7]で説明されます。

   o  Message protocols for transferring management information.  The
      first version of the SNMP message protocol is called SNMPv1 and is
      described in STD 15, RFC 1157 [8].  A second version of the SNMP
      message protocol, which is not an Internet standards track
      protocol, is called SNMPv2c and described is in RFC 1901 [9] and
      RFC 1906 [10].  The third version of the message protocol is
      called SNMPv3 and is described in RFC 1906 [10], RFC 2572 [11],
      and RFC 2574 [12].

o 経営情報を移すためのメッセージプロトコル。 SNMPメッセージプロトコルの最初のバージョンは、SNMPv1と呼ばれて、STD15、RFC1157[8]で説明されます。 プロトコル(インターネット標準化過程プロトコルでない)がSNMPv2cと呼ばれて、説明されるというSNMPメッセージの第2のバージョンがRFC1901[9]とRFC1906[10]にあります。 メッセージプロトコルの第3バージョンは、SNMPv3と呼ばれて、RFC1906[10]、RFC2572[11]、およびRFC2574[12]で説明されます。

   o  Protocol operations for accessing management information.  The
      first set of protocol operations and associated PDU formats is
      described in STD 15, RFC 1157 [8].  A second set of protocol
      operations and associated PDU formats is described in RFC 1905
      [13].

o 経営情報にアクセスするための操作について議定書の中で述べてください。 プロトコル操作と関連PDU形式の第一セットはSTD15、RFC1157[8]で説明されます。 2番目のセットのプロトコル操作と関連PDU形式はRFC1905[13]で説明されます。

   o  A set of fundamental applications described in RFC 2573 [14] and
      the view-based access control mechanism described in RFC 2575
      [15].

o 1セットの基礎的応用はRFCで2573[14]について説明しました、そして、視点ベースのアクセス管理機構はRFCで2575[15]について説明しました。

Ray & Abbi                  Standards Track                     [Page 2]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[2ページ]。

   A more detailed introduction to the current SNMP Management Framework
   can be found in RFC 2570 [16].

RFC2570[16]で現在のSNMP Management Frameworkへの、より詳細な紹介を見つけることができます。

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the mechanisms defined in the SMI.

管理オブジェクトはManagement Information基地と呼ばれた仮想情報店かMIBを通してアクセスされます。 MIBの物は、SMIで定義されたメカニズムを使用することで定義されます。

   This memo specifies a MIB module that is compliant to the SMIv2.  A
   MIB conforming to the SMIv1 can be produced through the appropriate
   translations.  The resulting translated MIB must be semantically
   equivalent, except where objects or events are omitted because no
   translation is possible (use of Counter64).  Some machine readable
   information in SMIv2 will be converted into textual descriptions in
   SMIv1 during the translation process.  However, this loss of machine
   readable information is not considered to change the semantics of the
   MIB.

このメモはSMIv2に対応であるMIBモジュールを指定します。 適切な翻訳でSMIv1に従うMIBは生産できます。 どんな翻訳も可能でないので(Counter64の使用)、結果として起こる翻訳されたMIBは物か出来事が省略されるところで意味的に同等でなければなりません。 SMIv2の何らかのマシンの読み込み可能な情報が翻訳の過程の間、SMIv1の原文の記述に変換されるでしょう。 しかしながら、マシンの読み込み可能な情報のこの損失がMIBの意味論を変えると考えられません。

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [17].

キーワード“MUST"、「必須NOT」が「必要です」、“SHALL"、「」、“SHOULD"、「「推薦され」て、「5月」の、そして、「任意」のNOTはRFC2119[17]で説明されるように本書では解釈されることであるべきですか?

3.  Introduction

3. 序論

   This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
   These definitions are based upon the specifications for the HDSL2 and
   SHDSL Embedded Operations Channel (EOC) as defined in ANSI
   T1E1.4/2000-006 [18] and ITU G.991.2 [19].

このドキュメントは、HDSL2/SHDSL線を管理するためにSNMP MIBについて説明します。 これらの定義はANSI T1E1.4/2000-006[18]とITU G.991.2[19]で定義されるようにHDSL2とSHDSL Embedded Operations Channel(EOC)のための仕様に基づいています。

   The MIB is located in the MIB tree under MIB 2 transmission, as
   discussed in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21])
   section of this document.

MIBはMIB木にMIB2送信で位置しています、MIB-2 Integrationで議論するように。(RFC1213[20]とRFC2863[21])部のこのドキュメント。

3.1.  Relationship of the HDSL2/SHDSL Line MIB to other MIBs

3.1. 他のMIBsへのHDSL2/SHDSL線MIBの関係

   This section outlines the relationship of this MIB with other MIBs
   described in RFCs.  Specifically, IF-MIB as presented in RFC 2863
   [21] is discussed.

他のMIBsがRFCsで説明されている状態で、このセクションはこのMIBの関係について概説します。 明確に、-、MIB、RFC2863に提示されるように、[21]について議論します。

3.1.1  General IF-MIB Integration (RFC 2863)

3.1.1 一般、-、MIB、統合(RFC2863)

   The HDSL2/SHDSL Line MIB specifies the detailed attributes of a data
   interface.  As such, it needs to integrate with RFC 2863 [21].  The
   IANA has assigned the following ifTypes to HDSL2 and SHDSL:

HDSL2/SHDSL線MIBはデータインタフェースの詳細な属性を指定します。 そういうものとして、それは、RFC2863[21]と統合する必要があります。 IANAは以下のifTypesをHDSL2とSHDSLに割り当てました:

Ray & Abbi                  Standards Track                     [Page 3]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[3ページ]。

   IANAifType ::= TEXTUAL-CONVENTION
       ...
   SYNTAX INTEGER {
       ...
       hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
       shdsl (169), -- Multirate HDSL2
       ...
       }

IANAifType:、:= 原文のコンベンション… 構文整数…hdsl2(168)--高いBit-レートDSL、2番目の世代shdsl(169)--多速度HDSL2…

   Note that the ifFixedLengthGroup from RFC 2863 [21] MUST be supported
   and that the ifRcvAddressGroup does not apply to this MIB.

RFC2863[21]からのifFixedLengthGroupを支持しなければならなくて、ifRcvAddressGroupがこのMIBに適用しないことに注意してください。

3.1.2  Usage of ifTable

3.1.2 ifTableの使用法

   The MIB branch identified by this ifType contains tables appropriate
   for this interface type.  Most such tables extend the ifEntry table,
   and are indexed by ifIndex.  For interfaces in systems implementing
   this MIB, those table entries indexed by ifIndex MUST be persistent.

このifTypeによって特定されたMIBブランチはこのインターフェース型にとって、適切なテーブルを含みます。 そのようなほとんどのテーブルが、ifEntryテーブルを広げていて、ifIndexによって索引をつけられます。 このMIBを実行するシステムのインタフェースに関しては、ifIndexによって索引をつけられたそれらのテーブル項目はしつこいに違いありません。

   The following attributes are part of the mandatory ifGeneral group in
   RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.

以下の属性は、RFC2863[21]の義務的なifGeneralグループの一部であり、HDSL2/SHDSL線MIBにコピーされません。

Ray & Abbi                  Standards Track                     [Page 4]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[4ページ]。

   ===================================================================
       ifIndex                  Interface index.

=================================================================== ifIndex Interfaceは索引をつけます。

       ifDescr                  See interfaces MIB [21].

ifDescr SeeはMIB[21]を連結します。

       ifType                   hdsl2(168) or shdsl(169).

ifType hdsl2(168)かshdsl(169)。

       ifSpeed                  Set as appropriate.
                                (This is fixed at 1552000 for HDSL2
                                lines)

適切な同じくらいifSpeed Set。 (これはHDSL2線への1552000で修理されています)

       ifPhysAddress            This object MUST have an octet string
                                with zero length.

ifPhysAddress This物には、ゼロ・レングスがある八重奏ストリングがなければなりません。

       ifAdminStatus            See interfaces MIB [21].

ifAdminStatus SeeはMIB[21]を連結します。

       ifOperStatus             See interfaces MIB [21].

ifOperStatus SeeはMIB[21]を連結します。

       ifLastChange             See interfaces MIB [21].

ifLastChange SeeはMIB[21]を連結します。

       ifName                   See interfaces MIB [21].

ifName SeeはMIB[21]を連結します。

       ifLinkUpDownTrapEnable   Default to enabled(1).

ifLinkUpDownTrapEnable Default、(1)を可能にしました。

       ifHighSpeed              Set as appropriate.
                                (For HDSL2 lines, this is fixed at 2)

適切な同じくらいifHighSpeed Set。 (HDSL2線において、これは2時に修理されています)

       ifConnectorPresent       Set as appropriate.

適切な同じくらいifConnectorPresent Set。

   ===================================================================
                   Figure 1: Use of ifTable Objects

=================================================================== 図1: ifTable物の使用

3.2 IANA Considerations

3.2 IANA問題

   The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single
   object identifier for its MODULE-IDENTITY.  The IANA has allocated
   this object identifier in the transmission subtree (48), defined in
   the SNMPv2-SMI MIB module.

HDSL2-SHDSL線MIBモジュールはMODULE-IDENTITYに、ただ一つの物の識別子の配分を必要とします。 IANAはSNMPv2-SMI MIBモジュールで定義されたトランスミッション下位木(48)におけるこの物の識別子を割り当てました。

4.  Conventions used in the MIB

4. MIBで使用されるコンベンション

4.1.  Naming Conventions

4.1. 命名規則

   A.  xtuC refers to a central site terminal unit;
       H2TU-C for HDSL2, or STU-C for SHDSL.
   B.  xtuR refers to a remote site terminal unit;
       H2TU-R for HDSL2, or STU-R for SHDSL.
   C.  xtu refers to a terminal unit; either an xtuC or xtuR.

A.xtuCは中央のサイト端末装置について言及します。 HDSL2のためのH2TU-C、またはSHDSLのためのSTU-C。 B.xtuRはリモートサイト端末装置について言及します。 HDSL2のためのH2TU-R、またはSHDSLのためのSTU-R。 C.xtuは端末装置について言及します。 xtuCかxtuRのどちらか。

Ray & Abbi                  Standards Track                     [Page 5]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[5ページ]。

   D.  xru refer to a regenerator unit;
       H2RU for HDSL2, or SRU for SHDSL.
   E.  xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
   F.  CRC is cyclic redundancy check [19].
   G.  ES means errored second [19].
   H.  LOSW means loss of sync word [19].
   I.  LOSWS means LOSW seconds [19].
   J.  SES means severely errored second [19].
   K.  SNR means signal-to-noise ratio [19].
   L.  UAS means unavailable second [19].

D.xruは再生器ユニットについて言及します。 HDSL2のためのH2RU、またはSHDSLのためのSRU。 E.xUはどんなHDSL2/SHDSLユニットについても言及します。 xtuかxruのどちらか。 F。 CRCは周期冗長検査[19]です。 G。 ES手段は2番目の[19]をerroredしました。 H。 LOSWは同時性単語[19]の損失を意味します。 I. LOSWSはLOSW秒[19]を意味します。 J。 SESは2番目の厳しくerroredされた[19]を意味します。 K。 SNRはSN比[19]を意味します。 L。 UASは2番目の入手できない[19]を意味します。

4.2.  Textual Conventions

4.2. 原文のコンベンション

   The following textual conventions are defined to reflect the line
   topology in the MIB (further discussed in the following section) and
   to define the behavior of the statistics to be maintained by an
   agent.

以下の原文のコンベンションは、MIB(さらに、以下のセクションで、議論する)に線トポロジーを反映して、エージェントによって維持される統計の振舞いを定義するために定義されます。

   o   Hdsl2ShdslUnitId:

o Hdsl2ShdslUnitId:

   Attributes with this syntax uniquely identify each unit in a
   HDSL2/SHDSL span.  It mirrors the EOC addressing mechanism:

この構文がある属性はHDSL2/SHDSLの長さで唯一各ユニットを特定します。 それはEOCアドレシングメカニズムを反映します:

   xtuC(1)                - CO terminal unit
   xtuR(2)                - CPE terminal unit
   xru1(3) .. xru8(10)    - regenerators, numbered from
                             central office side
   o   Hdsl2ShdslUnitSide:

xtuC(1)--CO端末装置xtuR(2)--xru1(3)CPE端末装置xru8(10)--電話局から付番された再生器はo Hdsl2ShdslUnitSideに面があります:

   Attributes with this syntax reference the two sides of a unit:

2は面があるユニットに関するこの構文参照がある属性:

   networkSide(1)   - N in figure 2, below
   customerSide(2)  - C in figure 2, below

networkSide(1)--customerSide(2)の下の2図のN--以下の2図のC

   o   Hdsl2ShdslWirePair:

o Hdsl2ShdslWirePair:

   Attributes with this syntax reference the wire-pairs connecting the
   units:

この構文がある属性はユニットを接続しながら、ワイヤ組に参照をつけます:

   wirePair1(1)   - First pair for HDSL2/SHDSL.

wirePair1(1)--まず最初に、HDSL2/SHDSLには、対にしてください。

   wirePair2(2)   - Optional second pair for SHDSL only.

wirePair2(2)--SHDSLのための2番目の任意の組。

   o   Hdsl2ShdslTransmissionModeType:

o Hdsl2ShdslTransmissionModeType:

   Attributes with this syntax specify the regional setting for a SHDSL
   line.  Specified as a BITS construct, the two mode types are:

この構文がある属性はSHDSL線に地方の設定を指定します。 BITS構造物として指定されていて、2つのモードタイプは以下の通りです。

Ray & Abbi                  Standards Track                     [Page 6]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[6ページ]。

   region1   - ITU-T G.991.2 Annex A
   region2   - ITU-T G.991.2 Annex B

region1--ITU-T G.991.2 Annex A region2--ITU-T G.991.2 Annex B

   o   Hdsl2ShdslPerfCurrDayCount:

o Hdsl2ShdslPerfCurrDayCount:

   Attributes with this syntax define the behavior of the 1-day (24
   hour) gauges found in the MIB.

この構文がある属性はMIBで見つけられた1日(24時間)のゲージの働きを定義します。

   o   Hdsl2Shdsl1DayIntervalCount:

o Hdsl2Shdsl1DayIntervalCount:

   Attributes with this syntax define the behavior of the 1-day (24
   hour) interval counters found in the MIB.

この構文がある属性はMIBで見つけられた1日(24時間)の間隔カウンタの振舞いを定義します。

   o   Hdsl2ShdslPerfTimeElapsed:

o Hdsl2ShdslPerfTimeElapsed:

   Attributes with this syntax define the behavior of the elapsed time
   counters found in the MIB.

この構文がある属性はMIBで見つけられた経過時間カウンタの振舞いを定義します。

   o   Hdsl2ShdslPerfIntervalThreshold:

o Hdsl2ShdslPerfIntervalThreshold:

   Attributes with this syntax define the behavior of the alarm
   thresholds found in the MIB.

この構文がある属性はMIBで見つけられたアラーム敷居の振舞いを定義します。

   o   Hdsl2ShdslClockReferenceType

o Hdsl2ShdslClockReferenceType

   Attributes with this syntax define the clock references for the
   HDSL2/SHDSL span.

この構文がある属性はHDSL2/SHDSLの長さの時計参照を定義します。

4.3.  Structure

4.3. 構造

   The MIB is structured into following MIB groups:

MIBは次のMIBグループに構造化されます:

   o   Span Configuration Group:

o 構成グループにかかってください:

   This group supports MIB objects for configuring parameters for the
   HDSL2/SHDSL span.  It contains the following table:

このグループは、HDSL2/SHDSLの長さのためのパラメタを構成するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslSpanConfTable

- hdsl2ShdslSpanConfTable

   o   Span Status Group:

o 地位集団にかかってください:

   This group supports MIB objects for retrieving span status
   information.  It contains the following table:

このグループは、長さ状態情報を検索するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslSpanStatusTable

- hdsl2ShdslSpanStatusTable

Ray & Abbi                  Standards Track                     [Page 7]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[7ページ]。

   o   Unit Inventory Group:

o ユニットはグループを棚卸しします:

   This group supports MIB objects for retrieving unit inventory
   information about units in HDSL2/SHDSL lines via the EOC. It contains
   the following table:

このグループは、EOCを通してHDSL2/SHDSL線でユニットに関するユニット在庫情報を検索するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslInventoryTable

- hdsl2ShdslInventoryTable

   o   Segment Endpoint Configuration Group:

o セグメント終点構成グループ:

   This group supports MIB objects for configuring parameters for the
   HDSL2/SHDSL segment endpoints.  It contains the following table:

このグループは、HDSL2/SHDSLセグメント終点のためのパラメタを構成するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslEndpointConfTable

- hdsl2ShdslEndpointConfTable

   o   Segment Endpoint Current Status/Performance Group:

o セグメントの終点の現在の状態/パフォーマンス・グループ:

   This group supports MIB objects that provide the current
   status/performance information relating to segment endpoints.  It
   contains the following table:

このグループはセグメント終点に関連する現在の状態/性能情報を提供するMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslEndpointCurrTable

- hdsl2ShdslEndpointCurrTable

   o   Segment Endpoint 15-Minute Interval Status/Performance Group:

o セグメントの終点の15分の間隔状態/パフォーマンス・グループ:

   This group supports MIB objects that provide historic
   status/performance information relating to segment endpoints in 15-
   minute intervals.  It contains the following table:

このグループは15の微小な間隔でセグメント終点に関連する歴史的な状態/性能情報を提供するMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2Shdsl15MinIntervalTable

- hdsl2Shdsl15MinIntervalTable

   o   Segment Endpoint 1-Day Interval Status/Performance Group:

o セグメントの終点の1日の間隔状態/パフォーマンス・グループ:

   This group supports MIB objects that provide historic
   status/performance information relating to segment endpoints in 1-day
   intervals.  It contains the following table:

このグループは1日間の間隔でセグメント終点に関連する歴史的な状態/性能情報を提供するMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2Shdsl1DayIntervalTable

- hdsl2Shdsl1DayIntervalTable

   o   Maintenance Group:

o 維持グループ:

   This group supports MIB objects for performing maintenance operations
   such as loopbacks for HDSL2/SHDSL lines.  It contains the following
   table(s):

このグループは、HDSL2/SHDSL線へのループバックなどの維持操作を実行するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslEndpointMaintTable
      - hdsl2ShdslUnitMaintTable

- hdsl2ShdslEndpointMaintTable--hdsl2ShdslUnitMaintTable

Ray & Abbi                  Standards Track                     [Page 8]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[8ページ]。

   o   Span Configuration Profile Group:

o 構成プロフィールグループにかかってください:

   This group supports MIB objects for defining configuration profiles
   for HDSL2/SHDSL Spans.  It contains the following table:

このグループは、HDSL2/SHDSL Spansのための構成プロフィールを定義するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslSpanConfProfileTable

- hdsl2ShdslSpanConfProfileTable

   o   Segment Endpoint Alarm Configuration Profile Group:

o セグメント終点アラーム構成プロフィールグループ:

   This group supports MIB objects for defining alarm configuration
   profiles for HDSL2/SHDSL Segment Endpoints.  It contains the
   following table:

このグループは、HDSL2/SHDSL Segment Endpointsのためのアラーム構成プロフィールを定義するためにMIB物を支えます。 それは以下のテーブルを含んでいます:

      - hdsl2ShdslEndpointAlarmConfProfileTable

- hdsl2ShdslEndpointAlarmConfProfileTable

   o   Notifications Group:

o 通知は分類されます:

   This group defines the notifications supported for HDSL2/SHDSL lines:

このグループはHDSL2/SHDSL線に支持された通知を定義します:

      - hdsl2ShdslLoopAttenCrossing
      - hdsl2ShdslSNRMarginCrossing
      - hdsl2ShdslPerfESThresh
      - hdsl2ShdslPerfSESThresh
      - hdsl2ShdslPerfCRCanomaliesThresh
      - hdsl2ShdslPerfLOSWSThresh
      - hdsl2ShdslPerfUASThresh
      - hdsl2ShdslSpanInvalidNumRepeaters
      - hdsl2ShdslLoopbackFailure
      - hdsl2ShdslpowerBackoff
      - hdsl2ShdsldeviceFault
      - hdsl2ShdsldcContinuityFault
      - hdsl2ShdslconfigInitFailure
      - hdsl2ShdslprotocolInitFailure
      - hdsl2ShdslnoNeighborPresent
      - hdsl2ShdslLocalPowerLoss

- hdsl2ShdslLoopAttenCrossing--hdsl2ShdslSNRMarginCrossing--hdsl2ShdslPerfESThresh--hdsl2ShdslPerfSESThresh--hdsl2ShdslPerfCRCanomaliesThresh--hdsl2ShdslPerfLOSWSThresh--hdsl2ShdslPerfUASThresh--hdsl2ShdslSpanInvalidNumRepeaters--hdsl2ShdslLoopbackFailure--hdsl2ShdslpowerBackoff--hdsl2ShdsldeviceFault--hdsl2ShdsldcContinuityFault--hdsl2ShdslconfigInitFailure--hdsl2ShdslprotocolInitFailure--hdsl2ShdslnoNeighborPresent--hdsl2ShdslLocalPowerLoss

4.3.1  Line Topology

4.3.1 線トポロジー

   An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
   central termination unit) and an xtuR (the remote termination unit).
   The line may optionally support up to 8 repeater/regenerator units
   (xru) as shown in the figure below.

HDSL2/SHDSL線は最低2ユニットから成ります--xtuC(中央の終了ユニット)とxtuR(リモート終了単位)。 線は以下の図に示されるように任意に、最大8リピータ/再生器ユニット(xru)を支持するかもしれません。

Ray & Abbi                  Standards Track                     [Page 9]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[9ページ]。

    <-- Network Side                            Customer Side -->

<--ネットワークサイド顧客側-->。

    |</////////////////// HDSL2/SHDSL Span ////////////////////>|

| </////////////////// HDSL2/SHDSL長さ////////////////////>|

            <~~~>       <~~~> HDSL2/SHDSL Segments  <~~~>

<。~~~><。~~~>HDSL2/SHDSLセグメント<。~~~>。

    +-------+   +-------+   +-------+       +-------+   +-------+
    +       C=1=N       C=1=N       C=..1..=N       C=1=N       +
    | xtuC  |   |  xru1 |   |  xru2 |       |  xru8 |   |  xtuR |
    +       C=2=N       C=2=N       C=..2..=N       C=2=N       +
    +-------+   +-------+   +-------+       +-------+   +-------+

+-------+ +-------+ +-------+ +-------+ +-------+ + Cは1=N C=1=N C=と等しいです。1..=N Cが1=N+と等しいです。| xtuC| | xru1| | xru2| | xru8| | xtuR| + Cは2=N C=2=N C=と等しいです。2..=N Cが2=N++と等しいです。-------+ +-------+ +-------+ +-------+ +-------+

    Key:  <////> HDSL2/SHDSL Span
          <~~~~> HDSL2/SHDSL Segment
          =1=    HDSL2/SHDSL wire-pair-1
          =2=    SHDSL optional wire-pair-2 (Not applicable to HDSL2)
          C      Customer Side Segment Endpoint (modem)
          N      Network Side Segment Endpoint (modem)

キー: <////>HDSL2/SHDSL長さ<。~~~~1本の=HDSL2/SHDSLワイヤ組>HDSL2/SHDSL Segment=1 =2はSHDSL任意のワイヤ組2(HDSL2に適切でない)C Customer Side Segment Endpoint(モデム)N Network Side Segment Endpointと等しいです。(モデム)

          Figure 2: General topology for an HDSL2/SHDSL Line

図2: HDSL2/SHDSL線のための一般トポロジー

4.4.  Counters, Interval Buckets and Thresholds

4.4. カウンタ、間隔バケツ、および敷居

   For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and
   UAS, there are event counters, current 15-minute and 0 to 96 15-
   minute history bucket(s) of "interval-counters", as well as current
   and 0 to 30 previous 1-day interval-counter(s).  Each current 15-
   minute event bucket has an associated threshold notification.

SNR Margin、Loop Attenuation、ES、SES、CRC例外、LOSW、およびUASのために、「間隔カウンタ」の歴史バケツがイベントカウンタ、現在の15分、および0〜96 15分あります、電流と0〜30台の前の1日間の間隔カウンタと同様に。 それぞれの現在の15微小なイベントバケツには、関連敷居通知があります。

   Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation in
   the MIB for invalid buckets.  In those cases where the data for an
   interval is suspect or known to be invalid, the agent MUST NOT report
   the interval.  If the current 15-minute event bucket is determined to
   be invalid, notifications based upon the value of the event bucket
   MUST NOT be generated.

RFC2493[22]とRFC2662[23]と異なって、表現が全く無効のバケツのためのMIBにありません。 間隔の間のデータが疑わしく、無効であることが知られているそれらの場合では、エージェントは間隔を報告してはいけません。 現在の15分のイベントバケツが無効であると決心しているなら、イベントバケツの値に基づく通知は発生してはいけません。

   Not reporting an interval will result in holes in the associated
   table.  For example, the table, hdsl2Shdsl15MinIntervalTable, is
   indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
   hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}.  If
   interval 12 is determined to be invalid but intervals 11 and 13 are
   valid, a Get Next operation on the indices .1.1.1.1.11 would return
   indices .1.1.1.1.13.

間隔を報告しないと、関連テーブルの穴はもたらされるでしょう。 例えば、テーブル(hdsl2Shdsl15MinIntervalTable)はifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePair、hdsl2Shdsl15MinIntervalNumberによって索引をつけられます。 .11はインデックスリスト.1を返すでしょう。間隔12が無効であると決心していますが、間隔11と13が有効であり、インデックスリスト.1.1におけるGet Next操作が.1である、.1、.1 .1 .1 .13。

Ray & Abbi                  Standards Track                    [Page 10]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[10ページ]。

   There is no requirement for an agent to ensure a fixed relationship
   between the start of a fifteen minute interval and any wall clock;
   however some implementations may align the fifteen minute intervals
   with quarter hours.  Likewise, an implementation may choose to align
   one day intervals with the start of a day.

エージェントが15分の間隔の始まりとどんな柱時計との固定関係も保証するという要件が全くありません。 しかしながら、いくつかの実現が15分の間隔を4分の1時間に一直線にするかもしれません。 同様に、実現は、ある日1日の始まりに間隔を並べるのを選ぶかもしれません。

   Counters are not reset when an xU is reinitialized, only when the
   agent is reset or reinitialized (or under specific request outside
   the scope of this MIB).

xUが再初期化されるとき、カウンタはリセットされません、エージェントがリセットされるか、または再初期化される場合にだけ(またはこのMIBの範囲の外での特定の要求で)。

4.5.  Profiles

4.5. プロフィール

   As a managed node can handle a large number of xUs, (e.g., hundreds
   or perhaps thousands of lines), provisioning every parameter on every
   xU may become burdensome.  Moreover, most lines are provisioned
   identically with the same set of parameters.  To simplify the
   provisioning process, this MIB makes use of profiles.  A profile is a
   set of parameters that can be shared by multiple lines using the same
   configuration.

管理されたノードが多くのxUsか、(例えば、数百か恐らく何千もの線)を扱うことができるとき、あらゆるxUに関するあらゆるパラメタに食糧を供給するのは重荷になるようになるかもしれません。 そのうえ、ほとんどの線が同様に同じセットのパラメタで食糧を供給されます。 食糧を供給することの過程を簡素化するために、このMIBはプロフィールを利用します。 プロフィールは複数の線で同じ構成を使用することで共有できる1セットのパラメタです。

   The following profiles are used in this MIB:

以下のプロフィールはこのMIBで使用されます:

   o  Span Configuration Profiles - Span configuration profiles contain
      parameters for configuring HDSL2/SHDSL spans.  They are defined in
      the hdsl2ShdslSpanConfProfileTable.  Since span configuration
      parameters are only applicable for SHDSL, the support for span
      configuration profiles are optional for HDSL2 interfaces.

o 長さConfiguration Profiles--長さ構成プロフィールはHDSL2/SHDSLがわたるのを構成するためのパラメタを含んでいます。 それらはhdsl2ShdslSpanConfProfileTableで定義されます。 SHDSLだけに、長さ設定パラメータが適切であるときに、HDSL2に、長さ構成プロフィールが任意であるので、サポートは連結します。

      Note that the configuration of the span dictates the behavior for
      each individual segment end point in the span.  If a different
      configuration is provisioned for any given segment end point
      within the span, the new configuration for this segment end point
      will override the span configuration for this segment end point
      only.

長さの構成が長さのそれぞれの個々のセグメントエンドポイントのための振舞いを決めることに注意してください。 異なった構成が長さの中のどんな与えられたセグメントエンドポイントのためにも食糧を供給されると、このセグメントエンドポイントのための新しい構成はこのセグメントエンドポイントだけのために長さ構成をくつがえすでしょう。

   o  Segment Endpoint Alarm Configuration Profiles - These profiles
      contain parameters for configuring alarm thresholds for
      HDSL2/SHDSL segment endpoints.  These profiles are defined in the
      hdsl2ShdslEndpointAlarmConfProfileTable.

o セグメントEndpoint Alarm Configuration Profiles--これらのプロフィールはHDSL2/SHDSLセグメント終点にアラーム敷居を構成するためのパラメタを含んでいます。 これらのプロフィールはhdsl2ShdslEndpointAlarmConfProfileTableで定義されます。

      The index value for this profile is a locally-unique
      administratively assigned name for the profile having the textual
      convention `SnmpAdminString' (RFC 2571 [1]).

このプロフィールのためのインデックス値はプロフィールのための原文のコンベンション'SnmpAdminString'を持っている局所的にユニークな行政上割り当てられた名前です。(RFC2571[1])。

   One or more lines may be configured to share parameters of a single
   profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = `silver') by
   setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value
   of this profile.  If a change is made to the profile, all lines that

1つ以上の線が、このプロフィールの値にhdsl2ShdslEndpointAlarmConfProfile物を設定することによって単一のプロフィール(例えば、hdsl2ShdslEndpointAlarmConfProfileは'銀'と等しい)のパラメタを共有するために構成されるかもしれません。 変更をプロフィールにするなら、すべてがそれを裏打ちします。

Ray & Abbi                  Standards Track                    [Page 11]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[11ページ]。

   refer to it will be reconfigured to the changed parameters.  Before a
   profile can be deleted or taken out of service it must be first
   unreferenced from all associated lines.

それを参照してください。変えられたパラメタに再構成されるでしょう。 プロフィールを削除するか、または使われなくなっていた状態で取ることができる前に、それは最初に、すべての関連線から参照されないに違いありません。

   Implementations MUST provide a default profile whose name is `DEFVAL'
   for each profile type.  The values of the associated parameters will
   be vendor specific unless otherwise indicated in this document.
   Before a line's profiles have been set, these profiles will be
   automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and
   hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate.  This
   default profile name, 'DEFVAL', is considered reserved in the context
   of profiles defined in this MIB.

実現は'DEFVAL'がだれの名前であるかというデフォルトプロフィールをそれぞれのプロフィールタイプに提供しなければなりません。 別の方法で本書では示されない場合、関連パラメタの値は業者特有になるでしょう。 1行設定される前に、これらのプロフィールは、適切であるところに'DEFVAL'にhdsl2ShdslEndpointAlarmConfProfileとhdsl2ShdslSpanConfProfileを設定することによって、自動的に使用されるでしょう。 このデフォルトプロフィール名('DEFVAL')はこのMIBで定義されたプロフィールの文脈で予約されていると考えられます。

   Profiles are created, assigned, and deleted dynamically using the
   profile name and profile row status in each of the four profile
   tables.

プロフィールは、ダイナミックにそれぞれの4個のプロフィールテーブルのプロフィール名とプロフィール列の状態を使用することで作成されて、割り当てられて、削除されます。

   Profile changes MUST take effect immediately.  These changes MAY
   result in a restart (hard reset or soft restart) of the units on the
   line.

外形変化はすぐに、効かなければなりません。 これらの変化は線におけるユニットの再開(困難なリセットか柔らかい再開)をもたらすかもしれません。

4.6.  Notifications

4.6. 通知

   The ability to generate the SNMP notifications coldStart/WarmStart
   (per [21]) which are per agent (e.g., per Digital Subscriber Line
   Access Multiplexer, or DSLAM, in such a device), and linkUp/linkDown
   (per [21]) which are per interface (i.e., HDSL2/SHDSL line) is
   required.

[21]) どれがエージェント(例えば、Digital Subscriber線あたりAccess Multiplexer、またはDSLAM、そのようなものの1台の装置)、およびlinkUp/linkDown単位であるか。SNMP通知coldStart/WarmStartを発生させる能力、((どれがインタフェース(すなわち、HDSL2/SHDSLは立ち並んでいる)単位であるかが[21])単位で必要です。

   A linkDown notification MAY be generated whenever any of ES, SES, CRC
   Anomaly, LOSW, or UAS event occurs.  The corresponding linkUp
   notification MAY be sent when all link failure conditions are
   cleared.

ES、SES、CRC Anomaly、LOSW、またはUAS出来事のどれかが起こるときはいつも、linkDown通知は発生するかもしれません。 すべてのリンク失敗状態をクリアするとき、対応するlinkUp通知を送るかもしれません。

   The notifications defined in this MIB are for initialization failure
   and for the threshold crossings associated with the following events:
   ES, SES, CRC Anomaly, LOSW, and UAS.  Each threshold has its own
   enable/threshold value.  When that value is 0, the notification is
   disabled.

初期化失敗と以下の出来事に関連している敷居交差点にはこのMIBで定義された通知があります: ES、SES、CRC異常、LOSW、およびUAS。 各敷居で、それ自身のものは/閾値を可能にします。 その値が0であるときに、通知は障害があります。

   The hdsl2ShdslEndpointCurrStatus is a bitmask representing all
   outstanding error conditions associated with a particular Segment
   Endpoint.  Note that since status of remote endpoints is obtained via
   the EOC, this information may be unavailable for units that are
   unreachable via EOC during a line error condition.  Therefore, not
   all conditions may always be included in its current status.
   Notifications corresponding to the bit fields in this object are
   defined.

hdsl2ShdslEndpointCurrStatusは特定のSegment Endpointに関連しているすべての傑出しているエラー条件を表すビットマスクです。 この情報がEOCを通して遠く離れた終点の状態を得るので線エラー条件の間のEOCを通して手が届かないユニットを入手できないかもしれないことに注意してください。 したがって、すべてではなく、状態は現在の状態にいつも含まれるかもしれません。 この物の噛み付いている分野に対応する通知は定義されます。

Ray & Abbi                  Standards Track                    [Page 12]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[12ページ]。

   Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm,
   are organized in a manner slightly different from that implied in the
   EOC specifications.  In the MIB, these alarm conditions are tied to
   the two thresholds hdsl2ShdslEndpointThreshSNRMargin and
   hdsl2ShdslEndpointThreshLoopAttenuation found in the
   hdsl2ShdslEndpointAlarmConfProfileTable.  In the EOC, the alarm
   conditions associated with these thresholds are per-unit.  In the
   MIB, these alarm conditions are per-endpoint.  For terminal units,
   this has no impact.  For repeaters, this implies an implementation
   variance where the agent in the terminal unit is responsible for
   detecting a threshold crossing.  As the reporting of a repeater
   detected alarm condition to the polling terminal unit occurs in the
   same EOC message as the reporting of the current SNR Margin and Loop
   Attenuation values, it is anticipated that this will have very little
   impact on agent implementation.

2つの警戒状態(SNR Margin AlarmとLoop Attenuation Alarm)が、EOC仕様で含意されたそれとわずかに異なった方法で組織化されます。 MIBでは、これらの警戒状態はhdsl2ShdslEndpointThreshSNRMarginとhdsl2ShdslEndpointThreshLoopAttenuationがhdsl2ShdslEndpointAlarmConfProfileTableで見つけた2つの敷居に結ばれます。 EOCでは、これらの敷居に関連している警戒状態はユニットです。 MIBでは、これらの警戒状態は終点です。 これには、何端末装置も、影響力が全くありません。 リピータに関しては、これは敷居が交差するのを検出するのに端末装置のエージェントが責任がある実現変化を含意します。 リピータの検出されたアラーム状態の投票している端末装置への報告が現在のSNR MarginとLoop Attenuation値の報告と同じEOCメッセージに起こるとき、これがエージェント実現のときにほとんど影響を与えさせないと予期されます。

   A threshold notification occurs whenever the corresponding current
   15-minute interval error counter becomes equal to, or exceeds the
   threshold value.  One notification may be sent per interval per
   interface.  Since the current 15-minute counter is reset to 0 every
   15 minutes, and if the condition persists, the notification may recur
   as  often as every 15 minutes.  For example, to get a notification
   whenever a "loss of" event occurs (but at most once every 15
   minutes), set the corresponding threshold to 1.  The agent will
   generate a notification when the event originally occurs.

対応する現在の15分の間隔誤りカウンタが等しくなるか、または閾値を超えているときはいつも、敷居通知は現れます。 1インタフェースあたりの間隔単位で1つの通知を送るかもしれません。 現在の15分のカウンタが15分毎に0にリセットされて、状態が持続しているなら、通知は15分毎と同じくらい頻繁に再発するかもしれません。 例えば通知を得る、いつ、「」 出来事の損失は発生して(15分あたり高々一度)、セットは1への対応する敷居であるか。 出来事が元々起こると、エージェントは通知を発生させるでしょう。

   Note that the Network Management System, or NMS, may receive a
   linkDown notification, as well, if enabled (via
   ifLinkUpDownTrapEnable [21]).  At the beginning of the next 15 minute
   interval, the counter is reset.  When the first second goes by and
   the event occurs, the current interval bucket will be 1, which equals
   the threshold, and the notification will be sent again.

可能にされるならまた、Network Management System、またはNMSがlinkDown通知を受け取るかもしれないことに注意してください。(ifLinkUpDownTrapEnable[21])を通して。 次の15分の間隔の始めに、カウンタはリセットされます。 最初の2番目が過ぎて、出来事が起こって、現在の間隔バケツが1になって、(敷居と等しいです)再び通知を送るとき。

   A hdsl2ShdslSpanInvalidNumRepeaters notification may be generated
   following completion of the discovery phase if the number of
   repeaters discovered on the line differs from the number of repeaters
   specified in hdsl2ShdslSpanConfNumRepeaters.  For those conditions
   where the number of provisioned repeaters is greater than those
   encountered during span discovery, all table entries associated with
   the nonexistent repeaters are to be discarded.  For those conditions
   where the number of provisioned repeaters is less than those
   encountered during span discovery, additional table entries are to be
   created using the default span configuration profile.

線の上で発見されたリピータの数がhdsl2ShdslSpanConfNumRepeatersで指定されたリピータの数と異なっているなら発見フェーズの完成に続いて、hdsl2ShdslSpanInvalidNumRepeaters通知は発生しているかもしれません。 食糧を供給されたリピータの数が長さ発見の間に遭遇するものより大きいそれらの状態に関しては、実在しないリピータに関連しているすべてのテーブル項目が捨てられることになっています。 食糧を供給されたリピータの数が長さ発見の間に遭遇するものより少ないそれらの状態に関しては、追加テーブル項目は、デフォルト長さ構成プロフィールを使用することで作成されることになっています。

Ray & Abbi                  Standards Track                    [Page 13]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[13ページ]。

5.  Conformance and Compliance

5. 順応と承諾

   For both HDSL2 and SHDSL lines, the following group(s) are mandatory:

HDSL2とSHDSL線の両方に、以下のグループは義務的です:

      hdsl2ShdslSpanConfGroup
      hdsl2ShdslSpanStatusGroup
      hdsl2ShdslInventoryGroup
      hdsl2ShdslEndpointConfGroup
      hdsl2Shdsl15MinIntervalGroup
      hdsl2Shdsl1DayIntervalGroup
      hdsl2ShdslMaintenanceGroup
      hdsl2ShdslEndpointAlarmConfGroup
      hdsl2ShdslNotificationGroup

hdsl2ShdslSpanConfGroup hdsl2ShdslSpanStatusGroup hdsl2ShdslInventoryGroup hdsl2ShdslEndpointConfGroup hdsl2Shdsl15MinIntervalGroup hdsl2Shdsl1DayIntervalGroup hdsl2ShdslMaintenanceGroup hdsl2ShdslEndpointAlarmConfGroup hdsl2ShdslNotificationGroup

   For HDSL2 lines, the following group(s) are optional:

HDSL2線において、以下のグループは任意です:

      hdsl2ShdslSpanConfProfileGroup
      hdsl2ShdslSpanShdslStatusGroup

hdsl2ShdslSpanConfProfileGroup hdsl2ShdslSpanShdslStatusGroup

6.  Definitions

6. 定義

HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN

HDSL2-SHDSL線MIB定義:、:= 始まってください。

IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Unsigned32,
Gauge32,
NOTIFICATION-TYPE,
Integer32,
transmission                  FROM SNMPv2-SMI
RowStatus,
TEXTUAL-CONVENTION            FROM SNMPv2-TC
ifIndex                       FROM IF-MIB
PerfCurrentCount,
PerfIntervalCount             FROM PerfHist-TC-MIB
SnmpAdminString               FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP            FROM SNMPv2-CONF;

IMPORTS MODULE-IDENTITY、OBJECT-TYPE、Counter32、Unsigned32、Gauge32、NOTIFICATION-TYPE、Integer32、トランスミッションFROM SNMPv2-SMI RowStatus、TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM、-、MIB PerfCurrentCount、PerfIntervalCount FROM PerfHist-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE、OBJECT-GROUP、NOTIFICATION-GROUP FROM SNMPv2-CONF。

hdsl2ShdslMIB MODULE-IDENTITY
    LAST-UPDATED "200205090000Z" -- May 9, 2002
    ORGANIZATION "ADSLMIB Working Group"
    CONTACT-INFO "WG-email:  adslmib@ietf.org
               Info:      https://www1.ietf.org/mailman/listinfo/adslmib
               Chair:     Mike Sneed

hdsl2ShdslMIBモジュールアイデンティティ最終更新日の"200205090000Z"--「以下をWGメールする」という2002年5月9日組織「ADSLMIBワーキンググループ」コンタクトインフォメーション adslmib@ietf.org インフォメーション: https://www1.ietf.org/mailman/listinfo/adslmib 議長: マイクSneed

Ray & Abbi                  Standards Track                    [Page 14]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[14ページ]。

               Postal:    P.O. Box 37324
                          Raleigh NC 27627-7324
               Email:     sneedmike@hotmail.com

郵便: 私書箱37324ローリーNC27627-7324はメールされます: sneedmike@hotmail.com

               Co-editor: Bob Ray
                          PESA Switching Systems, Inc.
               Postal:    330-A Wynn Drive
                          Huntsville, AL 35805 USA
               Email:     rray@pesa.com
               Phone:     +1 256 726 9200 ext. 142

共同エディタ: ボブレイペサ交換システムInc.郵便: 330-Aウィン・Drive AL35805ハンツビル(米国)はメールされます: rray@pesa.com 電話: +1 9200がextする256 726。 142

               Co-editor: Rajesh Abbi
                          Alcatel USA
               Postal:    2912 Wake Forest Road
                          Raleigh, NC 27609-7860 USA

共同エディタ: ラジェッシュAbbiアルカテル米国郵便: 2912年のウェイクフォーレストのRoad NC27609-7860ローリー(米国)

               Email:     Rajesh.Abbi@alcatel.com
               Phone:     +1 919 850 6194
              "

メール: Rajesh.Abbi@alcatel.com 電話: +1 919 850 6194 "

DESCRIPTION
     "This MIB module defines a collection of objects for managing
      HDSL2/SHDSL lines.  An agent may reside at either end of the
      line, however the MIB is designed to require no management
      communication between the modems beyond that inherent in the
      low-level EOC line protocol as defined in ANSI T1E1.4/2000-006
      (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)."
 REVISION "200205090000Z" -- May 9, 2002
 DESCRIPTION "Initial version, published as RFC 3276."

「このMIBモジュールはHDSL2/SHDSL線を管理しながら、物の収集を定義する」記述。 「しかしながら、エージェントは行のどちらの終わりにも住んでいるかもしれなくて、MIBは低レベルであるEOC線プロトコルで向こうのそんなに固有のモデムのマネジメント・コミュニケーションを全く必要としないようにANSI T1E1.4/2000-006(HDSL2線への)、またはITU G.991.2(SHDSL線への)で定義されるように設計されています。」 REVISION"200205090000Z"--「初期のバージョンであって、RFC3276として発行された」2002年5月9日記述。

 ::= { transmission 48 }

::= トランスミッション48

hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }

hdsl2ShdslMibObjects物の識別子:、:= hdsl2ShdslMIB1

-- Textual Conventions used in this MIB
--

-- このMIBで使用される原文のConventions--

Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "A gauge associated with interface performance measurements in
      a current 1-day (24 hour) measurement interval.

Hdsl2ShdslPerfCurrDayCount:、:= 「ゲージは現在の1日間(24時間)の測定間隔でのインタフェース性能測定に関連づけた」TEXTUAL-CONVENTION STATUSの現在の記述。

      The value of this gauge starts at zero at the beginning of an
      interval and is increased when associated events occur, until
      the end of the 1-day interval.  At that time the value of the
      gauge is stored in the previous 1-day history interval, as
      defined in a companion object of type

このゲージの値は、間隔の始めにゼロから出発して、関連出来事が起こるとき、増加されています、1日間の間隔の終わりまで。 その時、ゲージの値は前の1日間の歴史間隔に格納されます、タイプの仲間物で定義されるように

Ray & Abbi                  Standards Track                    [Page 15]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[15ページ]。

      Hdsl2Shdsl1DayIntevalCount, and the current interval gauge
      is restarted at zero.

ゲージがゼロで再開されるHdsl2Shdsl1DayIntevalCount、および現在の間隔。

      In the case where the agent has no valid data available for
      this interval the corresponding object instance is not
      available and upon a retrieval request a corresponding error
      message shall be returned to indicate that this instance does
      not exist.  Please note that zero is a valid value."
   SYNTAX  Gauge32

エージェントがこの間隔に利用可能などんな有効データも持っていない場合では、対応するオブジェクト例は利用可能ではありません、そして、検索要求のときに、この例が存在しないのを示すために対応するエラーメッセージを返すものとします。 「ゼロは有効値です。」 構文Gauge32

Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "A counter associated with interface performance measurements
      during the most previous 1-day (24 hour) measurement interval.
      The value of this gauge is equal to the value of the current
      day gauge, as defined in a companion object of type
      Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
      interval.

Hdsl2Shdsl1DayIntervalCount:、:= 「カウンタは前の最も多くの1日間(24時間)の測定間隔の間にインタフェース性能測定に関連づけた」TEXTUAL-CONVENTION STATUSの現在の記述。 このゲージの値は現在の日のゲージの値と等しいです、タイプHdsl2ShdslPerfCurrDayCountの仲間物で定義されるように、最新の間隔の終わりに。

      In the case where the agent has no valid data available for
      this interval the corresponding object instance is not
      available and upon a retrieval request a corresponding error
      message shall be returned to indicate that this instance does
      not exist."
   SYNTAX  Gauge32

「エージェントがこの間隔に利用可能などんな有効データも持っていない場合では、対応するオブジェクト例は利用可能ではありません、そして、検索要求のときに、この例が存在しないのを示すために対応するエラーメッセージを返すものとします。」 構文Gauge32

Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "The number of seconds that have elapsed since the beginning of
      the current measurement period.  If, for some reason, such as
      an adjustment in the system's time-of-day clock or the addition
      of a leap second, the current interval exceeds the maximum
      value, the agent will return the maximum value.

Hdsl2ShdslPerfTimeElapsed:、:= TEXTUAL-CONVENTION STATUSの現在の記述、「電流測定の期間の初め以来経過している秒数。」 現在の間隔がシステムの時刻時計での調整か閏秒の添加などの何らかの理由で最大値を超えていると、エージェントは最大値を返すでしょう。

      For 15 minute intervals, the range is limited to (0..899).
      For 24 hour intervals, the range is limited to (0..86399)."
   SYNTAX    Unsigned32(0..86399)

15分の間隔の間、範囲は(0 .899)に制限されます。 「24時間の間隔の間、範囲は(0 .86399)に制限されます。」 構文Unsigned32(0..86399)

Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "This convention defines a range of values that may be set in
      a fault threshold alarm control.  As the number of seconds in
      a 15-minute interval numbers at most 900, objects of this type
      may have a range of 0...900, where the value of 0 disables the
      alarm."

Hdsl2ShdslPerfIntervalThreshold:、:= TEXTUAL-CONVENTION STATUSの現在の記述、「このコンベンションは障害しきい値アラームコントロールで設定されるかもしれないさまざまな値を定義します」。 ほとんどの900における15分の間隔番号における秒数として、このタイプの物には、1つの範囲の0があるかもしれません…「900。」そこでは、0の値がアラームを無効にします。

Ray & Abbi                  Standards Track                    [Page 16]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[16ページ]。

   SYNTAX    Unsigned32(0..900)

構文Unsigned32(0..900)

Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "This is the unique identification for all units in a
      HDSL2/SHDSL Span.  It is based on the EOC unit addressing
      scheme with reference to the xtuC."
   SYNTAX    INTEGER
           {
           xtuC(1),
           xtuR(2),
           xru1(3),
           xru2(4),
           xru3(5),
           xru4(6),
           xru5(7),
           xru6(8),
           xru7(9),
           xru8(10)
           }

Hdsl2ShdslUnitId:、:= TEXTUAL-CONVENTION STATUSの現在の記述、「これはHDSL2/SHDSL Spanのすべてのユニットのためのユニークな識別です」。 「xtuCに関して計画を記述するEOCユニットに基づいています。」 構文整数xtuC(1)、xtuR(2)、xru1(3)、xru2(4)、xru3(5)、xru4(6)、xru5(7)、xru6(8)、xru7(9)、xru8(10)

Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "This is the referenced side of a HDSL2/SHDSL unit - Network
      or Customer side.  The side facing the Network is the Network
      side, while the side facing the Customer is the Customer side."
   SYNTAX    INTEGER
           {
           networkSide(1),
           customerSide(2)
           }

Hdsl2ShdslUnitSide:、:= TEXTUAL-CONVENTION STATUSの現在の記述、「これはHDSL2/SHDSLユニットの参照をつけられた側面です--ネットワークかCustomerが面があります」。 「Networkに面している側はNetwork側ですが、Customerに面している側はCustomer側です。」 構文整数networkSide(1)、customerSide(2)

Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "This is the referenced pair of wires in a HDSL2/SHDSL Segment.
      HDSL2 only supports a single pair (wirePair1), while SHDSL
      supports an optional second pair (wirePair2)."
   SYNTAX    INTEGER
           {
           wirePair1(1),
           wirePair2(2)
           }

Hdsl2ShdslWirePair:、:= TEXTUAL-CONVENTION STATUSの現在の記述、「これはHDSL2/SHDSL Segmentのワイヤの参照をつけられた組です」。 「HDSL2は1組(wirePair1)しか支持しませんが、SHDSLは2番目の任意の組(wirePair2)を支持します。」 構文整数wirePair1(1)、wirePair2(2)

Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
   STATUS    current

Hdsl2ShdslTransmissionModeType:、:= TEXTUAL-CONVENTION STATUS海流

Ray & Abbi                  Standards Track                    [Page 17]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[17ページ]。

   DESCRIPTION
     "Contains the regional setting of the HDSL2/SHDSL span,
     represented as a bit-map of possible settings. The various
     bit positions are:

記述は「可能な設定のしばらく地図として表されたHDSL2/SHDSLの長さの地方の設定を含んでいます」。 様々なビット位置は以下の通りです。

     Bit   Meaning      Description
     1     region 1     Indicates ITU-T G.991.2 Annex A.
     2     region 2     Indicates ITU-T G.991.2 Annex B."
   SYNTAX      BITS
           {
           region1(0),
           region2(1)
           }

「1つのビットMeaning記述1領域のIndicates ITU-T G.991.2 Annex A.2地域2Indicates ITU-T G.991.2 Annex B.」SYNTAX BITSregion1(0)、region2(1)

Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
   STATUS    current
   DESCRIPTION
     "The various STU-C symbol clock references for the
     HDSL2/SHDSL span, represented as an enumeration."
   SYNTAX    INTEGER
          {
          localClk(1),          -- Mode-1 per G991.2
          networkClk(2),        -- Mode-2 per G991.2
          dataOrNetworkClk(3),  -- Mode-3a per G991.2
          dataClk(4)            -- Mode-3b per G991.2
          }

Hdsl2ShdslClockReferenceType:、:= 「列挙として表されて、HDSL2/SHDSLの様々なSTU-Cシンボル時計参照はかかる」TEXTUAL-CONVENTION STATUSの現在の記述。 構文整数localClk(1)--1G991.2 networkClk(2)あたりモード-1--1G991.2 dataOrNetworkClk(3)あたりモード-2--1G991.2 dataClk(4)あたりのモード-3a--1G991.2あたりのモード-3b

-- Span Configuration Group
--

-- 構成グループにかかってください--

hdsl2ShdslSpanConfTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF Hdsl2ShdslSpanConfEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
     "This table supports overall configuration of HDSL2/SHDSL
      Spans.  Entries in this table MUST be maintained in a
      persistent manner."
   ::= { hdsl2ShdslMibObjects 1 }

hdsl2ShdslSpanConfTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「このテーブルはHDSL2/SHDSL Spansの総合的な構成を支持します」。 「しつこい方法でこのテーブルのエントリーを維持しなければなりません。」 ::= hdsl2ShdslMibObjects1

hdsl2ShdslSpanConfEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslSpanConfEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslSpanConfTable.  Each entry
      represents the complete Span in a single HDSL2/SHDSL line.
      It is indexed by the ifIndex of the associated HDSL2/SHDSL

hdsl2ShdslSpanConfEntry OBJECT-TYPE SYNTAX Hdsl2ShdslSpanConfEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslSpanConfTableのエントリー。」 各エントリーはただ一つのHDSL2/SHDSL線で完全なSpanを表します。 それは関連HDSL2/SHDSLのifIndexによって索引をつけられます。

Ray & Abbi                  Standards Track                    [Page 18]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[18ページ]。

      line."
   INDEX { ifIndex }
   ::= { hdsl2ShdslSpanConfTable 1 }

「立ち並んでください。」 ifIndexに索引をつけてください:、:= hdsl2ShdslSpanConfTable1

Hdsl2ShdslSpanConfEntry ::=
   SEQUENCE
   {
   hdsl2ShdslSpanConfNumRepeaters          Unsigned32,
   hdsl2ShdslSpanConfProfile               SnmpAdminString,
   hdsl2ShdslSpanConfAlarmProfile          SnmpAdminString
   }

Hdsl2ShdslSpanConfEntry:、:= 系列hdsl2ShdslSpanConfNumRepeaters Unsigned32、hdsl2ShdslSpanConfProfile SnmpAdminString、hdsl2ShdslSpanConfAlarmProfile SnmpAdminString

   hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
   SYNTAX      Unsigned32(0..8)
   UNITS       "repeaters"
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object provisions the number of repeaters/regenerators
     in this HDSL2/SHDSL Span."
   ::= { hdsl2ShdslSpanConfEntry 1 }

hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE SYNTAX Unsigned32(0 .8)UNITS「リピータ」マックス-ACCESSは「この物はこのHDSL2/SHDSL Spanのリピータ/再生器の数に食糧を供給すること」をSTATUSの現在の記述に読書して書きます。 ::= hdsl2ShdslSpanConfEntry1

hdsl2ShdslSpanConfProfile OBJECT-TYPE
   SYNTAX      SnmpAdminString (SIZE(1..32))
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object is a pointer to a span configuration profile in
     the hdsl2ShdslSpanConfProfileTable, which applies to this span.
     The value of this object is the index of the referenced profile
     in the hdsl2ShdslSpanConfProfileTable.  Note that span
     configuration profiles are only applicable to SHDSL lines.

hdsl2ShdslSpanConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1 .32))マックス-ACCESSは「この物はhdsl2ShdslSpanConfProfileTableの長さ構成プロフィールへのポインタです」をSTATUSの現在の記述に読書して書きます。hdsl2ShdslSpanConfProfileTableはこの長さに適用します。 この物の値はhdsl2ShdslSpanConfProfileTableの参照をつけられたプロフィールのインデックスです。 長さ構成プロフィールが単にSHDSL線に適切であることに注意してください。

     HDSL2 lines MUST reference the default profile, 'DEFVAL'.
     By default, this object will have the value 'DEFVAL' (the index
     of the default profile).

HDSL2線はデフォルトプロフィール、'DEFVAL'という参照がそうしなければなりません。 デフォルトで、この物には、値の'DEFVAL'(デフォルトプロフィールのインデックス)があるでしょう。

     Any attempt to set this object to a value that is not the value
     of the index for an active entry in the profile table,
     hdsl2ShdslSpanConfProfileTable, MUST be rejected."
   ::= { hdsl2ShdslSpanConfEntry 2 }

「プロフィールテーブルの活発なエントリーへのインデックスの値でない値にこの物を設定するどんな試み(hdsl2ShdslSpanConfProfileTable)も拒絶しなければなりません。」 ::= hdsl2ShdslSpanConfEntry2

hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE
   SYNTAX      SnmpAdminString (SIZE(1..32))
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object is a pointer to an Alarm configuration profile in

hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1 .32))マックス-ACCESSは「この物は中のAlarm構成プロフィールへのポインタです」をSTATUSの現在の記述に読書して書きます。

Ray & Abbi                  Standards Track                    [Page 19]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[19ページ]。

     the hdsl2ShdslEndpointAlarmConfProfileTable.  The value of this
     object is the index of the referenced profile in the
     hdsl2ShdslEndpointAlarmConfProfileTable.  The alarm threshold
     configuration in the referenced profile will be used by default
     for all segment endpoints in this span.  Individual endpoints
     may override this profile by explicitly specifying some other
     profile in the hdsl2ShdslEndpointConfTable.  By default, this
     object will have the value 'DEFVAL' (the index of the default
     profile).

hdsl2ShdslEndpointAlarmConfProfileTable。 この物の値はhdsl2ShdslEndpointAlarmConfProfileTableの参照をつけられたプロフィールのインデックスです。 参照をつけられたプロフィールでのアラーム敷居構成はこの長さのすべてのセグメント終点にデフォルトで使用されるでしょう。 明らかにhdsl2ShdslEndpointConfTableのある他のプロフィールを指定することによって、個々の終点はこのプロフィールに優越するかもしれません。 デフォルトで、この物には、値の'DEFVAL'(デフォルトプロフィールのインデックス)があるでしょう。

     Any attempt to set this object to a value that is not the value
     of the index for an active entry in the profile table,
     hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
   ::= { hdsl2ShdslSpanConfEntry 3 }

「プロフィールテーブルの活発なエントリーへのインデックスの値でない値にこの物を設定するどんな試み(hdsl2ShdslEndpointAlarmConfProfileTable)も拒絶しなければなりません。」 ::= hdsl2ShdslSpanConfEntry3

-- Span Status Group
--

-- 地位集団にかかってください--

hdsl2ShdslSpanStatusTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF Hdsl2ShdslSpanStatusEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
     "This table provides overall status information of
      HDSL2/SHDSL spans.  This table contains live data from
      equipment.  As such, it is NOT persistent."
   ::= { hdsl2ShdslMibObjects 2 }

「このテーブルはHDSL2/SHDSLの長さの総合的な状態情報を提供する」hdsl2ShdslSpanStatusTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 このテーブルは設備からのライブデータを含んでいます。 「そういうものとして、それはしつこくはありません。」 ::= hdsl2ShdslMibObjects2

hdsl2ShdslSpanStatusEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslSpanStatusEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslSpanStatusTable.  Each entry
      represents the complete span in a single HDSL2/SHDSL line.
      It is indexed by the ifIndex of the associated HDSL2/SHDSL
      line."
   INDEX { ifIndex }
   ::= { hdsl2ShdslSpanStatusTable 1 }

hdsl2ShdslSpanStatusEntry OBJECT-TYPE SYNTAX Hdsl2ShdslSpanStatusEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslSpanStatusTableのエントリー。」 各エントリーはただ一つのHDSL2/SHDSL線における完全な長さを表します。 「それは関連HDSL2/SHDSL線のifIndexによって索引をつけられます。」 ifIndexに索引をつけてください:、:= hdsl2ShdslSpanStatusTable1

Hdsl2ShdslSpanStatusEntry ::=
   SEQUENCE
   {
   hdsl2ShdslStatusNumAvailRepeaters        Unsigned32,
   hdsl2ShdslStatusMaxAttainableLineRate    Unsigned32,
   hdsl2ShdslStatusActualLineRate           Unsigned32,
   hdsl2ShdslStatusTransmissionModeCurrent
             Hdsl2ShdslTransmissionModeType

Hdsl2ShdslSpanStatusEntry:、:= 系列、hdsl2ShdslStatusNumAvailRepeaters Unsigned32、hdsl2ShdslStatusMaxAttainableLineRate Unsigned32、hdsl2ShdslStatusActualLineRate Unsigned32、hdsl2ShdslStatusTransmissionModeCurrent Hdsl2ShdslTransmissionModeType

Ray & Abbi                  Standards Track                    [Page 20]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[20ページ]。

   }

}

hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
   SYNTAX      Unsigned32(0..8)
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the actual number of repeaters/regenerators
      discovered in this HDSL2/SHDSL span."
   ::= { hdsl2ShdslSpanStatusEntry 1 }

hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE SYNTAX Unsigned32(0 .8)のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「このHDSL2/SHDSLの長さで発見されたリピータ/再生器の実数を含んでいます」。 ::= hdsl2ShdslSpanStatusEntry1

hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
   SYNTAX      Unsigned32(0..4112000)
   UNITS       "bps"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the maximum attainable line rate in this HDSL2/SHDSL
      span.  This object provides the maximum rate the line is
      capable of achieving.  This is based upon measurements made
      during line probing."
   ::= { hdsl2ShdslSpanStatusEntry 2 }

hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE SYNTAX Unsigned32(0 .4112000)UNITS「ビーピーエス」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「このHDSL2/SHDSLの長さに達成できる最大のライン料率を保管しています」。 この物は線が達成できる最高率を提供します。 「これは線の調べの間にされた測定に基づいています。」 ::= hdsl2ShdslSpanStatusEntry2

hdsl2ShdslStatusActualLineRate OBJECT-TYPE
   SYNTAX      Unsigned32(0..4112000)
   UNITS       "bps"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the actual line rate in this HDSL2/SHDSL span.  This
     should equal ifSpeed."
   ::= { hdsl2ShdslSpanStatusEntry 3 }

hdsl2ShdslStatusActualLineRate OBJECT-TYPE SYNTAX Unsigned32(0 .4112000)UNITS「ビーピーエス」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「このHDSL2/SHDSLの長さに実際のライン料率を保管しています」。 「これはifSpeedと等しくあるべきです。」 ::= hdsl2ShdslSpanStatusEntry3

hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
   SYNTAX      Hdsl2ShdslTransmissionModeType
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the current Power Spectral Density (PSD) regional
      setting of the HDSL2/SHDSL span."
   ::= { hdsl2ShdslSpanStatusEntry 4 }

hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE SYNTAX Hdsl2ShdslTransmissionModeTypeのマックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「HDSL2/SHDSLの長さの現在のPower Spectral Density(PSD)の地方の設定を含んでいます」。 ::= hdsl2ShdslSpanStatusEntry4

-- Unit Inventory Group
--

-- ユニットはグループを棚卸しします--

hdsl2ShdslInventoryTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF Hdsl2ShdslInventoryEntry
   MAX-ACCESS not-accessible

アクセスしやすくないhdsl2ShdslInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntryマックス-ACCESS

Ray & Abbi                  Standards Track                    [Page 21]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[21ページ]。

   STATUS     current
   DESCRIPTION
     "This table supports retrieval of unit inventory information
      available via the EOC from units in a HDSL2/SHDSL line.

「HDSL2/SHDSLのユニットからのEOCを通して利用可能なユニット在庫情報のこのテーブルサポート検索は裏打ちする」STATUSの現在の記述。

      Entries in this table are dynamically created during the
      line discovery process.  The life cycle for these entries
      is as follows:

このテーブルのエントリーは線発見の過程の間、ダイナミックに作成されます。 これらのエントリーへのライフサイクルは以下の通りです:

         - xtu discovers a device, either a far-end xtu or an xru
         - an inventory table entry is created for the device
         - the line goes down for whatever reason
         - inventory table entries for unreachable devices are
           destroyed.

- xtuは装置を発見します、遠端xtuかxruのどちらか--目録テーブルエントリーは装置のために作成されます--線はいかなる理由でも落ちます--手の届かない装置のための目録テーブルエントリーは破壊されます。

      As these entries are created/destroyed dynamically, they
      are NOT persistent."
   ::= { hdsl2ShdslMibObjects 3 }

「これらのエントリーがダイナミックに作成されるか、または破壊されるとき、それらはしつこくはありません。」 ::= hdsl2ShdslMibObjects3

hdsl2ShdslInventoryEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslInventoryEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslInventoryTable.  Each entry
      represents inventory information for a single unit in a
      HDSL2/SHDSL line.  It is indexed by the ifIndex of the
      HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
      associated unit."
   INDEX { ifIndex, hdsl2ShdslInvIndex }
   ::= { hdsl2ShdslInventoryTable 1 }

hdsl2ShdslInventoryEntry OBJECT-TYPE SYNTAX Hdsl2ShdslInventoryEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslInventoryTableのエントリー。」 各エントリーはHDSL2/SHDSL線で単一の単位在庫情報を表します。 「それはHDSL2/SHDSL線のifIndexと関連ユニットのHdsl2ShdslUnitIdによって索引をつけられます。」 ifIndex、hdsl2ShdslInvIndexに索引をつけてください:、:= hdsl2ShdslInventoryTable1

Hdsl2ShdslInventoryEntry ::=
   SEQUENCE
   {
   hdsl2ShdslInvIndex                      Hdsl2ShdslUnitId,
   hdsl2ShdslInvVendorID                   OCTET STRING,
   hdsl2ShdslInvVendorModelNumber          OCTET STRING,
   hdsl2ShdslInvVendorSerialNumber         OCTET STRING,
   hdsl2ShdslInvVendorEOCSoftwareVersion   Integer32,
   hdsl2ShdslInvStandardVersion            Integer32,
   hdsl2ShdslInvVendorListNumber           OCTET STRING,
   hdsl2ShdslInvVendorIssueNumber          OCTET STRING,
   hdsl2ShdslInvVendorSoftwareVersion      OCTET STRING,
   hdsl2ShdslInvEquipmentCode              OCTET STRING,
   hdsl2ShdslInvVendorOther                OCTET STRING,
   hdsl2ShdslInvTransmissionModeCapability
                         Hdsl2ShdslTransmissionModeType

Hdsl2ShdslInventoryEntry:、:= 系列、hdsl2ShdslInvIndex Hdsl2ShdslUnitId、hdsl2ShdslInvVendorID八重奏ストリング、hdsl2ShdslInvVendorModelNumber八重奏ストリング、hdsl2ShdslInvVendorSerialNumber八重奏ストリング、hdsl2ShdslInvVendorEOCSoftwareVersion Integer32、hdsl2ShdslInvStandardVersion Integer32; hdsl2ShdslInvVendorListNumber八重奏ストリング、hdsl2ShdslInvVendorIssueNumber八重奏ストリング、hdsl2ShdslInvVendorSoftwareVersion八重奏ストリング、hdsl2ShdslInvEquipmentCode八重奏ストリング、hdsl2ShdslInvVendorOther八重奏ストリング、hdsl2ShdslInvTransmissionModeCapability Hdsl2ShdslTransmissionModeType

Ray & Abbi                  Standards Track                    [Page 22]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[22ページ]。

   }

}

hdsl2ShdslInvIndex OBJECT-TYPE
   SYNTAX      Hdsl2ShdslUnitId
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
      "Each entry in this table corresponds to a physical element
      in a HDSL2/SHDSL Span.  It is based on the EOC unit addressing
      scheme with reference to the xtuC."
   ::= { hdsl2ShdslInventoryEntry 1 }

hdsl2ShdslInvIndex OBJECT-TYPE SYNTAX Hdsl2ShdslUnitIdのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「このテーブルの各エントリーはHDSL2/SHDSL Spanの物理的な要素に対応しています」。 「xtuCに関して計画を記述するEOCユニットに基づいています。」 ::= hdsl2ShdslInventoryEntry1

hdsl2ShdslInvVendorID OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(8))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor ID as reported in an Inventory Response message."
   ::= { hdsl2ShdslInventoryEntry 2 }

hdsl2ShdslInvVendorID OBJECT-TYPE SYNTAX OCTET STRING、(SIZE(8)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述「Inventory Responseメッセージで報告される業者ID。」 ::= hdsl2ShdslInventoryEntry2

hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(12))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor model number as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 3 }

hdsl2ShdslInvVendorModelNumber OBJECT-TYPE SYNTAX OCTET STRING、(「業者モデルはInventory Responseメッセージで報告されるように付番する」SIZE(12)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry3

hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(12))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor serial number as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 4 }

hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE SYNTAX OCTET STRING、(「Inventory Responseの報告されるとしての業者通し番号は通信させる」SIZE(12)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry4

hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
   SYNTAX      Integer32
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor EOC version as reported in a Discovery Response
      message."
   ::= { hdsl2ShdslInventoryEntry 5 }

「ディスカバリーResponseの報告されるとしての業者EOCバージョンは通信させる」hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE SYNTAX Integer32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry5

hdsl2ShdslInvStandardVersion OBJECT-TYPE

hdsl2ShdslInvStandardVersionオブジェクト・タイプ

Ray & Abbi                  Standards Track                    [Page 23]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[23ページ]。

   SYNTAX      Integer32
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Version of the HDSL2/SHDSL standard implemented, as reported
      in an Inventory Response message."
   ::= { hdsl2ShdslInventoryEntry 6 }

「HDSL2/SHDSL規格のバージョンはInventory Responseメッセージで報告されるように実行した」SYNTAX Integer32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry6

hdsl2ShdslInvVendorListNumber OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(3))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor list number as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 7 }

hdsl2ShdslInvVendorListNumber OBJECT-TYPE SYNTAX OCTET STRING、(「業者リストはInventory Responseメッセージで報告されるように付番する」SIZE(3)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry7

hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(2))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor issue number as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 8 }

hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE SYNTAX OCTET STRING、(「業者問題はInventory Responseメッセージで報告されるように付番する」SIZE(2)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry8

hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(6))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Vendor software version as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 9 }

hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE SYNTAX OCTET STRING、(「Inventory Responseの報告されるとしてのメーカー・ソフトウエアバージョンは通信させる」SIZE(6)) MAX-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= hdsl2ShdslInventoryEntry9

hdsl2ShdslInvEquipmentCode OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(10))
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Equipment code conforming to ANSI T1.213, Coded Identification
      of Equipment Entities."
   ::= { hdsl2ShdslInventoryEntry 10 }

hdsl2ShdslInvEquipmentCode OBJECT-TYPE SYNTAX OCTET STRING、(SIZE(10)) MAX-ACCESSの読書だけのSTATUSの現在の記述「設備はANSI T1.213への従うことをコード化します、Equipment EntitiesのCoded Identification。」 ::= hdsl2ShdslInventoryEntry10

hdsl2ShdslInvVendorOther OBJECT-TYPE
   SYNTAX      OCTET STRING(SIZE(12))
   MAX-ACCESS  read-only
   STATUS      current

hdsl2ShdslInvVendorOther OBJECT-TYPE SYNTAX OCTET STRING、(SIZE(12)) MAX-ACCESS書き込み禁止STATUS海流

Ray & Abbi                  Standards Track                    [Page 24]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[24ページ]。

   DESCRIPTION
     "Other vendor information as reported in an Inventory Response
      message."
   ::= { hdsl2ShdslInventoryEntry 11 }

「Inventory Responseの報告されるとしての他の売り主情報は通信させる」記述。 ::= hdsl2ShdslInventoryEntry11

hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
   SYNTAX      Hdsl2ShdslTransmissionModeType
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the transmission mode capability of the SHDSL unit."
   ::= { hdsl2ShdslInventoryEntry 12 }

hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE SYNTAX Hdsl2ShdslTransmissionModeTypeのマックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「SHDSLユニットの転送方式能力を含んでいます」。 ::= hdsl2ShdslInventoryEntry12

-- Segment Endpoint Configuration Group
--

-- セグメント終点構成グループ--

hdsl2ShdslEndpointConfTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslEndpointConfEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table supports configuration parameters for segment
      endpoints in a HDSL2/SHDSL line.  As this table is indexed
      by ifIndex, it MUST be maintained in a persistent manner."
   ::= { hdsl2ShdslMibObjects 4 }

「HDSL2/SHDSLのセグメント終点のためのこのテーブルサポート設定パラメータは裏打ちする」hdsl2ShdslEndpointConfTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 「このテーブルがifIndexによって索引をつけられるとき、しつこい方法でそれを維持しなければなりません。」 ::= hdsl2ShdslMibObjects4

hdsl2ShdslEndpointConfEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslEndpointConfEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslEndpointConfTable.  Each entry
      represents a single segment endpoint in a HDSL2/SHDSL line.
      It is indexed by the ifIndex of the HDSL2/SHDSL line, the
      UnitId of the associated unit, the side of the unit, and the
      wire-pair of the associated modem."
   INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
           hdsl2ShdslEndpointWirePair}
   ::= { hdsl2ShdslEndpointConfTable 1 }

hdsl2ShdslEndpointConfEntry OBJECT-TYPE SYNTAX Hdsl2ShdslEndpointConfEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslEndpointConfTableのエントリー。」 各エントリーはHDSL2/SHDSL線で単一のセグメント終点を表します。 「それはHDSL2/SHDSL線のifIndex、関連ユニットのUnitId、ユニットの側面、および関連モデムのワイヤ組によって索引をつけられます。」 ifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePairに索引をつけてください:、:= hdsl2ShdslEndpointConfTable1

Hdsl2ShdslEndpointConfEntry ::=
   SEQUENCE
   {
   hdsl2ShdslEndpointSide                   Hdsl2ShdslUnitSide,
   hdsl2ShdslEndpointWirePair               Hdsl2ShdslWirePair,
   hdsl2ShdslEndpointAlarmConfProfile       SnmpAdminString
   }

Hdsl2ShdslEndpointConfEntry:、:= 系列hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide、hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair、hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString

Ray & Abbi                  Standards Track                    [Page 25]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[25ページ]。

hdsl2ShdslEndpointSide OBJECT-TYPE
   SYNTAX      Hdsl2ShdslUnitSide
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "The side of the unit associated with this segment endpoint -
      Network/Customer side - as per the Hdsl2ShdslUnitSide textual
      convention."
   ::= { hdsl2ShdslEndpointConfEntry 1 }

「ユニットの側面はHdsl2ShdslUnitSideの原文のコンベンションに従ってこのセグメント終点(ネットワーク/顧客側)に関連づけた」hdsl2ShdslEndpointSide OBJECT-TYPE SYNTAX Hdsl2ShdslUnitSideのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 ::= hdsl2ShdslEndpointConfEntry1

hdsl2ShdslEndpointWirePair OBJECT-TYPE
   SYNTAX      Hdsl2ShdslWirePair
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "The wire-pair of the modem associated with this segment
      endpoint as per the Hdsl2ShdslWirePair textual convention."
   ::= { hdsl2ShdslEndpointConfEntry 2 }

アクセスしやすくないhdsl2ShdslEndpointWirePair OBJECT-TYPE SYNTAX Hdsl2ShdslWirePairのSTATUS現在の記述マックス-ACCESS「Hdsl2ShdslWirePairに従ってこのセグメント終点に関連しているモデムのワイヤ組の原文のコンベンション。」 ::= hdsl2ShdslEndpointConfEntry2

hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
   SYNTAX      SnmpAdminString (SIZE(0..32))
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object configures the alarm threshold values to be used
      for this segment endpoint.  The values are obtained from the
      alarm configuration profile referenced by this object.  The
      value of this object is the index of the referenced profile in
      the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-
      length SnmpAdminString).  If the value is a zero-length
      SnmpAdminString, the endpoint uses the default Alarm
      Configuration Profile for the associated span as per the
      hdsl2ShdslSpanConfAlarmProfile object in the
      hdsl2ShdslSpanConfTable.  The default value of this object is
      a zero-length SnmpAdminString.

hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0 .32))マックス-ACCESSは「この物はこのセグメント終点に使用されるためにアラーム閾値を構成すること」をSTATUSの現在の記述に読書して書きます。 この物によって参照をつけられるアラーム構成プロフィールから値を得ます。 この物の値はhdsl2ShdslEndpointAlarmConfProfileTable、またはNULL(無の長さのSnmpAdminString)の参照をつけられたプロフィールのインデックスです。 値が無の長さのSnmpAdminStringであるなら、終点はhdsl2ShdslSpanConfTableのhdsl2ShdslSpanConfAlarmProfile物に従って関連長さにデフォルトAlarm Configuration Profileを使用します。 この物のデフォルト値は無の長さのSnmpAdminStringです。

      Any attempt to set this object to a value that is not the value
      of the index for an active entry in the profile table,
      hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
   ::= { hdsl2ShdslEndpointConfEntry 3 }

「プロフィールテーブルの活発なエントリーへのインデックスの値でない値にこの物を設定するどんな試み(hdsl2ShdslEndpointAlarmConfProfileTable)も拒絶しなければなりません。」 ::= hdsl2ShdslEndpointConfEntry3

-- Segment Endpoint Current Status/Performance Group
--

-- セグメントの終点の現在の状態/パフォーマンス・グループ--

hdsl2ShdslEndpointCurrTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
   MAX-ACCESS  not-accessible
   STATUS      current

hdsl2ShdslEndpointCurrTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntryのマックス-ACCESSのアクセスしやすくないSTATUS海流

Ray & Abbi                  Standards Track                    [Page 26]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[26ページ]。

   DESCRIPTION
     "This table contains current status and performance information
      for segment endpoints in HDSL2/SHDSL Lines.  As with other
      tables in this MIB indexed by ifIndex, entries in this table
      MUST be maintained in a persistent manner."
   ::= { hdsl2ShdslMibObjects 5 }

記述、「このテーブルはHDSL2/SHDSL線にセグメント終点のための現在の状態と性能情報を含んでいます」。 「他のテーブルがifIndexによって索引をつけられたこのMIBにある状態でしつこい方法でこのテーブルのエントリーを維持しなければならないように。」 ::= hdsl2ShdslMibObjects5

hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslEndpointCurrEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslEndpointCurrTable.  Each entry
     contains status and performance information relating to a
     single segment endpoint.  It is indexed by the ifIndex of the
     HDSL2/SHDSL line, the UnitId of the associated unit, the side
     of the unit, and the wire-pair of the associated modem."
   INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
           hdsl2ShdslEndpointWirePair }
   ::= { hdsl2ShdslEndpointCurrTable 1 }

hdsl2ShdslEndpointCurrEntry OBJECT-TYPE SYNTAX Hdsl2ShdslEndpointCurrEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslEndpointCurrTableのエントリー。」 各エントリーは単一のセグメント終点に関連する状態と性能情報を含んでいます。 「それはHDSL2/SHDSL線のifIndex、関連ユニットのUnitId、ユニットの側面、および関連モデムのワイヤ組によって索引をつけられます。」 ifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePairに索引をつけてください:、:= hdsl2ShdslEndpointCurrTable1

Hdsl2ShdslEndpointCurrEntry ::=
   SEQUENCE
   {
   hdsl2ShdslEndpointCurrAtn                Integer32,
   hdsl2ShdslEndpointCurrSnrMgn             Integer32,
   hdsl2ShdslEndpointCurrStatus             BITS,
   hdsl2ShdslEndpointES                     Counter32,
   hdsl2ShdslEndpointSES                    Counter32,
   hdsl2ShdslEndpointCRCanomalies           Counter32,
   hdsl2ShdslEndpointLOSWS                  Counter32,
   hdsl2ShdslEndpointUAS                    Counter32,
   hdsl2ShdslEndpointCurr15MinTimeElapsed
                             Hdsl2ShdslPerfTimeElapsed,
   hdsl2ShdslEndpointCurr15MinES            PerfCurrentCount,
   hdsl2ShdslEndpointCurr15MinSES           PerfCurrentCount,
   hdsl2ShdslEndpointCurr15MinCRCanomalies  PerfCurrentCount,
   hdsl2ShdslEndpointCurr15MinLOSWS         PerfCurrentCount,
   hdsl2ShdslEndpointCurr15MinUAS           PerfCurrentCount,
   hdsl2ShdslEndpointCurr1DayTimeElapsed
                             Hdsl2ShdslPerfTimeElapsed,
   hdsl2ShdslEndpointCurr1DayES
                             Hdsl2ShdslPerfCurrDayCount,
   hdsl2ShdslEndpointCurr1DaySES
                             Hdsl2ShdslPerfCurrDayCount,
   hdsl2ShdslEndpointCurr1DayCRCanomalies
                             Hdsl2ShdslPerfCurrDayCount,
   hdsl2ShdslEndpointCurr1DayLOSWS

Hdsl2ShdslEndpointCurrEntry:、:= 系列、hdsl2ShdslEndpointCurrAtn Integer32、hdsl2ShdslEndpointCurrSnrMgn Integer32、hdsl2ShdslEndpointCurrStatusビット、hdsl2ShdslEndpointES Counter32、hdsl2ShdslEndpointSES Counter32、hdsl2ShdslEndpointCRCanomalies Counter32、hdsl2ShdslEndpointLOSWS Counter32、hdsl2ShdslEndpointUAS Counter32、hdsl2ShdslEndpointCurr15MinTimeElapsed Hdsl2ShdslPerfTimeElapsed、hdsl2ShdslEndpointCurr15MinES PerfCurrentCount、hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount; hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount、hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount、hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount、hdsl2ShdslEndpointCurr1DayTimeElapsed Hdsl2ShdslPerfTimeElapsed、hdsl2ShdslEndpointCurr1DayES Hdsl2ShdslPerfCurrDayCount、hdsl2ShdslEndpointCurr1DaySES Hdsl2ShdslPerfCurrDayCount、hdsl2ShdslEndpointCurr1DayCRCanomalies Hdsl2ShdslPerfCurrDayCount、hdsl2ShdslEndpointCurr1DayLOSWS

Ray & Abbi                  Standards Track                    [Page 27]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[27ページ]。

                             Hdsl2ShdslPerfCurrDayCount,
   hdsl2ShdslEndpointCurr1DayUAS
                             Hdsl2ShdslPerfCurrDayCount
   }

Hdsl2ShdslPerfCurrDayCount、hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount

hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
   SYNTAX      Integer32(-127..128)
   UNITS       "dB"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "The current loop attenuation for this endpoint as reported in
      a Network or Customer Side Performance Status message."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 1 }

「Networkで報告されるこの終点のための現在の輪の減衰かCustomer SideパフォーマンスStatusが通信させる」hdsl2ShdslEndpointCurrAtn OBJECT-TYPE SYNTAX Integer32(-127 .128)UNITS「dB」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry1

hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
   SYNTAX      Integer32(-127..128)
   UNITS       "dB"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "The current SNR margin for this endpoint as reported in a
      Status Response/SNR message."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 2 }

「Status Response/SNRの報告されるとしてのこの終点への現在のSNRマージンは通信させる」hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE SYNTAX Integer32(-127 .128)UNITS「dB」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry2

hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
   SYNTAX      BITS
               {
               noDefect(0),
               powerBackoff(1),
               deviceFault(2),
               dcContinuityFault(3),
               snrMarginAlarm(4),
               loopAttenuationAlarm(5),
               loswFailureAlarm(6),
               configInitFailure(7),
               protocolInitFailure(8),
               noNeighborPresent(9),
               loopbackActive(10)
               }
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Contains the current state of the endpoint.  This is a
     bitmap of possible conditions. The various bit positions
     are:

hdsl2ShdslEndpointCurrStatus OBJECT-TYPE SYNTAX BITS、noDefect(0)、powerBackoff(1)、deviceFault(2)、dcContinuityFault(3)、snrMarginAlarm(4)、loopAttenuationAlarm(5)、loswFailureAlarm(6)、configInitFailure(7)、protocolInitFailure(8)、noNeighborPresent(9)、loopbackActive(10)、マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「終点の現状を含んでいます」。 これは可能な状態のビットマップです。 様々なビット位置は以下の通りです。

Ray & Abbi                  Standards Track                    [Page 28]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[28ページ]。

     noDefect               There no defects on the line.

noDefect Thereノー、は線の上で亡命します。

     powerBackoff           Indicates enhanced Power Backoff.

powerBackoff IndicatesはPower Backoffを高めました。

     deviceFault            Indicates a vendor-dependent
                            diagnostic or self-test fault
                            has been detected.

deviceFault Indicatesのa業者依存する病気の特徴か自己診断欠点が検出されました。

     dcContinuityFault      Indicates vendor-dependent
                            conditions that interfere with
                            span powering such as short and
                            open circuits.

短くて開いているサーキットなどを長さの動かすことを妨げるdcContinuityFault Indicates業者依存条件。

     snrMarginAlarm         Indicates that the SNR margin
                            has dropped below the alarm threshold.

SNRマージンがアラーム敷居より下であるまで落としたsnrMarginAlarm Indicates。

     loopAttenuationAlarm   Indicates that the loop attenuation
                            exceeds the alarm threshold.

loopAttenuationAlarm Indicates、輪の減衰はアラーム敷居を超えています。

     loswFailureAlarm       Indicates a forward LOSW alarm.

前進のLOSWが驚かせるloswFailureAlarm Indicates。

     configInitFailure      Endpoint failure during initialization
                            due to paired endpoint not able to
                            support requested configuration.

支持できない対にされた終点による初期化の間のconfigInitFailure Endpointの故障は構成を要求しました。

     protocolInitFailure    Endpoint failure during initialization
                            due to incompatible protocol used by
                            the paired endpoint.

対にされた終点によって使用される両立しないプロトコルによる初期化の間のprotocolInitFailure Endpointの故障。

     noNeighborPresent      Endpoint failure during initialization
                            due to no activation sequence detected
                            from paired endpoint.

対にされた終点から検出されなかった起動系列による全く初期化の間のnoNeighborPresent Endpointの故障。

     loopbackActive         A loopback is currently active at this
                            Segment Endpoint.

loopbackActive Aループバックは現在、このSegment Endpointでアクティブです。

     This is intended to supplement ifOperStatus.  Note that there
     is a 1-1 relationship between the status bits defined in this
     object and the notification thresholds defined elsewhere in
     this MIB."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 3 }

これがifOperStatusを補うことを意図します。 「この物で定義されたステータスビットとこのMIBのほかの場所で定義された通知敷居との1-1関係があることに注意してください。」 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry3

hdsl2ShdslEndpointES OBJECT-TYPE
   SYNTAX      Counter32
   UNITS       "seconds"
   MAX-ACCESS  read-only
   STATUS      current

hdsl2ShdslEndpointES OBJECT-TYPE SYNTAX Counter32 UNITS「秒」マックス-ACCESS書き込み禁止STATUS海流

Ray & Abbi                  Standards Track                    [Page 29]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[29ページ]。

   DESCRIPTION
     "Count of Errored Seconds (ES) on this endpoint since the xU
      was last restarted."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 4 }

記述は「xUが最後に再開されたので、この終点のErrored Seconds(ES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry4

hdsl2ShdslEndpointSES OBJECT-TYPE
   SYNTAX       Counter32
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Severely Errored Seconds (SES) on this endpoint
      since the xU was last restarted."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 5 }

hdsl2ShdslEndpointSES OBJECT-TYPE SYNTAX Counter32 UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「xUが最後に再開されたので、この終点のSeverely Errored Seconds(SES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry5

hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
   SYNTAX       Counter32
   UNITS        "detected CRC Anomalies"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of CRC anomalies on this endpoint since the xU was
      last restarted."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 6 }

hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE SYNTAX Counter32 UNITSの「検出されたCRC Anomalies」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「xUが最後に再開されたので、この終点でCRC例外を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry6

hdsl2ShdslEndpointLOSWS OBJECT-TYPE
   SYNTAX       Counter32
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Loss of Sync Word (LOSW) Seconds on this endpoint
      since the xU was last restarted."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 7 }

hdsl2ShdslEndpointLOSWS OBJECT-TYPE SYNTAX Counter32 UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「xUが最後に再開されたので、この終点のSync Word(LOSW)秒のLossを数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry7

hdsl2ShdslEndpointUAS OBJECT-TYPE
   SYNTAX       Counter32
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Unavailable Seconds (UAS) on this endpoint since
      the xU was last restarted."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"

hdsl2ShdslEndpointUAS OBJECT-TYPE SYNTAX Counter32 UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「xUが最後に再開されたので、この終点のUnavailable Seconds(UAS)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ

Ray & Abbi                  Standards Track                    [Page 30]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[30ページ]。

   ::= { hdsl2ShdslEndpointCurrEntry 8 }

::= hdsl2ShdslEndpointCurrEntry8

hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfTimeElapsed
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Total elapsed seconds in the current 15-minute interval."
   ::= { hdsl2ShdslEndpointCurrEntry 9 }

hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE SYNTAX Hdsl2ShdslPerfTimeElapsed UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「現在の15分の間隔で経過した秒を合計します」。 ::= hdsl2ShdslEndpointCurrEntry9

hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
   SYNTAX       PerfCurrentCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Errored Seconds (ES) in the current 15-minute
      interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 10 }

hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE SYNTAX PerfCurrentCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「現在の15分の間隔でErrored Seconds(ES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry10

hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
   SYNTAX       PerfCurrentCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Severely Errored Seconds (SES) in the current
      15-minute interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 11 }

hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE SYNTAX PerfCurrentCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「現在の15分の間隔でSeverely Errored Seconds(SES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry11

hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
   SYNTAX       PerfCurrentCount
   UNITS        "detected CRC Anomalies"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of CRC anomalies in the current 15-minute interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 12 }

hdsl2ShdslEndpointCurr15MinCRCanomaliesの「検出されたCRC Anomalies」マックス-ACCESSの書き込み禁止のSTATUSの現在のOBJECT-TYPE SYNTAX PerfCurrentCount UNITS記述は「現在の15分の間隔でCRC例外を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry12

hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
   SYNTAX       PerfCurrentCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current

hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE SYNTAX PerfCurrentCount UNITS「秒」マックス-ACCESS書き込み禁止STATUS海流

Ray & Abbi                  Standards Track                    [Page 31]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[31ページ]。

   DESCRIPTION
     "Count of Loss of Sync Word (LOSW) Seconds in the current
      15-minute interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 13 }

記述は「現在の15分の間隔でSync Word(LOSW)秒のLossを数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry13

hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
   SYNTAX       PerfCurrentCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Unavailable Seconds (UAS) in the current 15-minute
      interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 14 }

hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE SYNTAX PerfCurrentCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「現在の15分の間隔でUnavailable Seconds(UAS)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry14

hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfTimeElapsed
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Number of seconds that have elapsed since the beginning of
      the current 1-day interval."
   ::= { hdsl2ShdslEndpointCurrEntry 15 }

hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE SYNTAX Hdsl2ShdslPerfTimeElapsed UNITSはマックス-ACCESSの書き込み禁止のSTATUSの現在の記述を「後援します」。「1日の現在の間隔の始まり以来経過している秒数。」 ::= hdsl2ShdslEndpointCurrEntry15

hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfCurrDayCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Errored Seconds (ES) during the current day as
      measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 16 }

hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2ShdslEndpointCurr1DayTimeElapsedによって測定されるように現在の日の間、Errored Seconds(ES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry16

hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfCurrDayCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Severely Errored Seconds (SES) during the current
      day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 17 }

hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2ShdslEndpointCurr1DayTimeElapsedによって測定されるように現在の日の間、Severely Errored Seconds(SES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry17

Ray & Abbi                  Standards Track                    [Page 32]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[32ページ]。

hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfCurrDayCount
   UNITS        "detected CRC Anomalies"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of CRC anomalies during the current day as measured
      by hdsl2ShdslEndpointCurr1DayTimeElapsed."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 18 }

hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS「検出されたCRC Anomalies」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2ShdslEndpointCurr1DayTimeElapsedによって測定されるように現在の日の間、CRC例外を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry18

hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfCurrDayCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Loss of Sync Word (LOSW) Seconds during the current
      day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 19 }

hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2ShdslEndpointCurr1DayTimeElapsedによって測定されるように現在の日間のSync Word(LOSW)秒のLossを数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry19

hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfCurrDayCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Unavailable Seconds (UAS) during the current day as
      measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2ShdslEndpointCurrEntry 20 }

hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2ShdslEndpointCurr1DayTimeElapsedによって測定されるように現在の日の間、Unavailable Seconds(UAS)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2ShdslEndpointCurrEntry20

-- Segment Endpoint 15-Minute Interval Status/Performance Group
--

-- セグメントの終点の15分の間隔状態/パフォーマンス・グループ--

hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table provides one row for each HDSL2/SHDSL endpoint
      performance data collection interval.  This table contains
      live data from equipment.  As such, it is NOT persistent."
   ::= { hdsl2ShdslMibObjects 6 }

「このテーブルはそれぞれのHDSL2/SHDSL終点性能データ収集間隔あたり1つの列を提供する」hdsl2Shdsl15MinIntervalTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 このテーブルは設備からのライブデータを含んでいます。 「そういうものとして、それはしつこくはありません。」 ::= hdsl2ShdslMibObjects6

hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
   SYNTAX      Hdsl2Shdsl15MinIntervalEntry

hdsl2Shdsl15MinIntervalEntryオブジェクト・タイプ構文Hdsl2Shdsl15MinIntervalEntry

Ray & Abbi                  Standards Track                    [Page 33]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[33ページ]。

   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2Shdsl15MinIntervalTable."
   INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
           hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
   ::= { hdsl2Shdsl15MinIntervalTable 1 }

マックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2Shdsl15MinIntervalTableのエントリー。」 ifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePair、hdsl2Shdsl15MinIntervalNumberに索引をつけてください:、:= hdsl2Shdsl15MinIntervalTable1

Hdsl2Shdsl15MinIntervalEntry ::=
   SEQUENCE
   {
   hdsl2Shdsl15MinIntervalNumber         Unsigned32,
   hdsl2Shdsl15MinIntervalES             PerfIntervalCount,
   hdsl2Shdsl15MinIntervalSES            PerfIntervalCount,
   hdsl2Shdsl15MinIntervalCRCanomalies   PerfIntervalCount,
   hdsl2Shdsl15MinIntervalLOSWS          PerfIntervalCount,
   hdsl2Shdsl15MinIntervalUAS            PerfIntervalCount
   }

Hdsl2Shdsl15MinIntervalEntry:、:= 系列hdsl2Shdsl15MinIntervalNumber Unsigned32、hdsl2Shdsl15MinIntervalES PerfIntervalCount、hdsl2Shdsl15MinIntervalSES PerfIntervalCount、hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount、hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount、hdsl2Shdsl15MinIntervalUAS PerfIntervalCount

hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
   SYNTAX      Unsigned32(1..96)
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "Performance Data Interval number. 1 is the the most recent
      previous interval; interval 96 is 24 hours ago. Intervals
      2..96 are optional."
   ::= { hdsl2Shdsl15MinIntervalEntry 1 }

アクセスしやすくないhdsl2Shdsl15MinIntervalNumber OBJECT-TYPE SYNTAX Unsigned32(1 .96)のSTATUS現在の記述マックス-ACCESS「パフォーマンスData Interval番号。」 1は前の最新の間隔です。 24時間前に間隔96はそうです。 間隔2。「96は任意です。」 ::= hdsl2Shdsl15MinIntervalEntry1

hdsl2Shdsl15MinIntervalES OBJECT-TYPE
   SYNTAX      PerfIntervalCount
   UNITS       "seconds"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Count of Errored Seconds (ES) during the interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl15MinIntervalEntry 2 }

hdsl2Shdsl15MinIntervalES OBJECT-TYPE SYNTAX PerfIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「間隔の間、Errored Seconds(ES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl15MinIntervalEntry2

hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
   SYNTAX      PerfIntervalCount
   UNITS       "seconds"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Count of Severely Errored Seconds (SES) during the interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl15MinIntervalEntry 3 }

hdsl2Shdsl15MinIntervalSES OBJECT-TYPE SYNTAX PerfIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「間隔の間、Severely Errored Seconds(SES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl15MinIntervalEntry3

Ray & Abbi                  Standards Track                    [Page 34]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[34ページ]。

hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
   SYNTAX      PerfIntervalCount
   UNITS       "detected CRC Anomalies"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Count of CRC anomalies during the interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl15MinIntervalEntry 4 }

hdsl2Shdsl15MinIntervalCRCanomaliesの「検出されたCRC Anomalies」マックス-ACCESSの書き込み禁止のSTATUSの現在のOBJECT-TYPE SYNTAX PerfIntervalCount UNITS記述は「間隔の間、CRC例外を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl15MinIntervalEntry4

hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
   SYNTAX      PerfIntervalCount
   UNITS       "seconds"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Count of Loss of Sync Word (LOSW) Seconds during the
      interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl15MinIntervalEntry 5 }

hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE SYNTAX PerfIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「間隔の間のSync Word(LOSW)秒のLossを数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl15MinIntervalEntry5

hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
   SYNTAX      PerfIntervalCount
   UNITS       "seconds"
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "Count of Unavailable Seconds (UAS) during the interval."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl15MinIntervalEntry 6 }

hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE SYNTAX PerfIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「間隔の間、Unavailable Seconds(UAS)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl15MinIntervalEntry6

-- Segment Endpoint 1-Day Interval Status/Performance Group
--

-- セグメントの終点の1日の間隔状態/パフォーマンス・グループ--

hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table provides one row for each HDSL2/SHDSL endpoint
      performance data collection interval.  This table contains
      live data from equipment.  As such, it is NOT persistent."
   ::= { hdsl2ShdslMibObjects 7 }

「このテーブルはそれぞれのHDSL2/SHDSL終点性能データ収集間隔あたり1つの列を提供する」hdsl2Shdsl1DayIntervalTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 このテーブルは設備からのライブデータを含んでいます。 「そういうものとして、それはしつこくはありません。」 ::= hdsl2ShdslMibObjects7

hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
   SYNTAX      Hdsl2Shdsl1DayIntervalEntry
   MAX-ACCESS  not-accessible
   STATUS      current

hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalEntryのマックス-ACCESSのアクセスしやすくないSTATUS海流

Ray & Abbi                  Standards Track                    [Page 35]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[35ページ]。

   DESCRIPTION
     "An entry in the hdsl2Shdsl1DayIntervalTable."
   INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
           hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
   ::= { hdsl2Shdsl1DayIntervalTable 1 }

記述、「hdsl2Shdsl1DayIntervalTableのエントリー。」 ifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePair、hdsl2Shdsl1DayIntervalNumberに索引をつけてください:、:= hdsl2Shdsl1DayIntervalTable1

Hdsl2Shdsl1DayIntervalEntry ::=
   SEQUENCE
   {
   hdsl2Shdsl1DayIntervalNumber         Unsigned32,
   hdsl2Shdsl1DayIntervalMoniSecs       Hdsl2ShdslPerfTimeElapsed,
   hdsl2Shdsl1DayIntervalES             Hdsl2Shdsl1DayIntervalCount,
   hdsl2Shdsl1DayIntervalSES            Hdsl2Shdsl1DayIntervalCount,
   hdsl2Shdsl1DayIntervalCRCanomalies   Hdsl2Shdsl1DayIntervalCount,
   hdsl2Shdsl1DayIntervalLOSWS          Hdsl2Shdsl1DayIntervalCount,
   hdsl2Shdsl1DayIntervalUAS            Hdsl2Shdsl1DayIntervalCount
   }

Hdsl2Shdsl1DayIntervalEntry:、:= 系列hdsl2Shdsl1DayIntervalNumber Unsigned32、hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed、hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount、hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount、hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount、hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount、hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount

hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
   SYNTAX      Unsigned32(1..30)
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "History Data Interval number. Interval 1 is the the most
      recent previous day; interval 30 is 30 days ago. Intervals
      2..30 are optional."
   ::= { hdsl2Shdsl1DayIntervalEntry 1 }

アクセスしやすくないhdsl2Shdsl1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32(1 .30)のSTATUS現在の記述マックス-ACCESS「歴史Data Interval番号。」 間隔1は前の最新の日です。 30日前に間隔30はそうです。 間隔2。「30は任意です。」 ::= hdsl2Shdsl1DayIntervalEntry1

hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
   SYNTAX       Hdsl2ShdslPerfTimeElapsed
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "The amount of time in the 1-day interval over which the
      performance monitoring information is actually counted.
      This value will be the same as the interval duration except
      in a situation where performance monitoring data could not
      be collected for any reason."
   ::= { hdsl2Shdsl1DayIntervalEntry 2 }

hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE SYNTAX Hdsl2ShdslPerfTimeElapsed UNITSはマックス-ACCESSの書き込み禁止のSTATUSの現在の記述を「後援します」。「性能監視情報が実際に数えられる1日間の間隔の時間。」 「どんな理由でも性能のモニターしているデータを集めることができなかった状況を除いて、この値は間隔持続時間と同じになるでしょう。」 ::= hdsl2Shdsl1DayIntervalEntry2

hdsl2Shdsl1DayIntervalES OBJECT-TYPE
   SYNTAX       Hdsl2Shdsl1DayIntervalCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Errored Seconds (ES) during the 1-day interval as

書き込み禁止のSTATUSの現在の記述が「1日間の間隔の間のErrored Seconds(ES)は数える」hdsl2Shdsl1DayIntervalES OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS「秒」マックス-ACCESS

Ray & Abbi                  Standards Track                    [Page 36]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[36ページ]。

      measured by hdsl2Shdsl1DayIntervalMoniSecs."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl1DayIntervalEntry 3 }

「hdsl2Shdsl1DayIntervalMoniSecsによって測定されます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl1DayIntervalEntry3

hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
   SYNTAX       Hdsl2Shdsl1DayIntervalCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Severely Errored Seconds (SES) during the 1-day
      interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl1DayIntervalEntry 4 }

hdsl2Shdsl1DayIntervalSES OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2Shdsl1DayIntervalMoniSecsによって測定されるように1日間の間隔の間、Severely Errored Seconds(SES)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl1DayIntervalEntry4

hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
   SYNTAX       Hdsl2Shdsl1DayIntervalCount
   UNITS        "detected CRC Anomalies"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of CRC anomalies during the 1-day interval as
      measured by hdsl2Shdsl1DayIntervalMoniSecs."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl1DayIntervalEntry 5 }

hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS「検出されたCRC Anomalies」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2Shdsl1DayIntervalMoniSecsによって測定されるように1日間の間隔の間、CRC例外を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl1DayIntervalEntry5

hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
   SYNTAX       Hdsl2Shdsl1DayIntervalCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Loss of Sync Word (LOSW) Seconds during the 1-day
      interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl1DayIntervalEntry 6 }

hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2Shdsl1DayIntervalMoniSecsによって測定されるように1日間の間隔の間のSync Word(LOSW)秒のLossを数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl1DayIntervalEntry6

hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
   SYNTAX       Hdsl2Shdsl1DayIntervalCount
   UNITS        "seconds"
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
     "Count of Unavailable Seconds (UAS) during the 1-day interval
      as measured by hdsl2Shdsl1DayIntervalMoniSecs."
   REFERENCE   "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
   ::= { hdsl2Shdsl1DayIntervalEntry 7 }

hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS「秒」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述は「hdsl2Shdsl1DayIntervalMoniSecsによって測定されるように1日間の間隔の間、Unavailable Seconds(UAS)を数えます」。 参照「HDSL2セクション7.5.3.7」。 SHDSL部9.5 .5 0.7インチ:、:= hdsl2Shdsl1DayIntervalEntry7

Ray & Abbi                  Standards Track                    [Page 37]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[37ページ]。

-- Maintenance Group
--

-- 維持グループ--

hdsl2ShdslEndpointMaintTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table supports maintenance operations (eg. loopbacks)
      to be performed on HDSL2/SHDSL segment endpoints.  This table
      contains live data from equipment.  As such, it is NOT
      persistent."
   ::= { hdsl2ShdslMibObjects 8 }

「HDSL2/SHDSLセグメント終点に実行されて、このテーブルは維持操作(例えば、ループバック)を支持する」hdsl2ShdslEndpointMaintTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 このテーブルは設備からのライブデータを含んでいます。 「そういうものとして、それはしつこくはありません。」 ::= hdsl2ShdslMibObjects8

hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslEndpointMaintEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslEndpointMaintTable.  Each entry
      corresponds to a single segment endpoint, and is indexed by the
      ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
      unit and the side of the unit."
   INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
   ::= { hdsl2ShdslEndpointMaintTable 1 }

hdsl2ShdslEndpointMaintEntry OBJECT-TYPE SYNTAX Hdsl2ShdslEndpointMaintEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslEndpointMaintTableのエントリー。」 「各エントリーは、単一のセグメント終点に対応している、HDSL2/SHDSL線、関連ユニットのUnitId、およびユニットの側面のifIndexによって索引をつけられます。」 ifIndex、hdsl2ShdslInvIndex、hdsl2ShdslEndpointSideに索引をつけてください:、:= hdsl2ShdslEndpointMaintTable1

Hdsl2ShdslEndpointMaintEntry ::=
   SEQUENCE
   {
   hdsl2ShdslMaintLoopbackConfig      INTEGER,
   hdsl2ShdslMaintTipRingReversal     INTEGER,
   hdsl2ShdslMaintPowerBackOff        INTEGER,
   hdsl2ShdslMaintSoftRestart         INTEGER
   }

Hdsl2ShdslEndpointMaintEntry:、:= 系列hdsl2ShdslMaintLoopbackConfig整数、hdsl2ShdslMaintTipRingReversal整数、hdsl2ShdslMaintPowerBackOff整数、hdsl2ShdslMaintSoftRestart整数

hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
   SYNTAX      INTEGER
               {
               noLoopback(1),
               normalLoopback(2),
               specialLoopback(3)
               }
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object controls configuration of loopbacks for the
      associated segment endpoint.  The status of the loopback
      is obtained via the hdsl2ShdslEndpointCurrStatus object."

hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE SYNTAX INTEGER、noLoopback(1)、normalLoopback(2)、specialLoopback(3)は「関連セグメント終点にループバックの構成を制御これが反対するします」マックス-ACCESSが、STATUS現在の記述を読書して書く。 「hdsl2ShdslEndpointCurrStatus物を通してループバックの状態を得ます。」

Ray & Abbi                  Standards Track                    [Page 38]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[38ページ]。

   ::= { hdsl2ShdslEndpointMaintEntry 1 }

::= hdsl2ShdslEndpointMaintEntry1

hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
   SYNTAX      INTEGER
               {
               normal(1),
               reversed(2)
               }
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "This object indicates the state of the tip/ring pair at the
      associated segment endpoint."
   ::= { hdsl2ShdslEndpointMaintEntry 2 }

hdsl2ShdslMaintTipRingReversal OBJECT-TYPE SYNTAX INTEGER、正常な(1)で、逆にされる、(2)、マックス-ACCESSの読書だけのSTATUSの現在の記述は「関連セグメント終点でチップ/リング組の状態を示これが反対するします」。 ::= hdsl2ShdslEndpointMaintEntry2

hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
   SYNTAX      INTEGER
               {
               default(1),
               enhanced(2)
               }
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object configures the receiver at the associated
      segment endpoint to operate in default or enhanced power
      backoff mode."
   ::= { hdsl2ShdslEndpointMaintEntry 3 }

hdsl2ShdslMaintPowerBackOff OBJECT-TYPE SYNTAX INTEGER、デフォルト(1)であって、高められる、(2)、マックス-ACCESSは「この物はデフォルトか高められたパワーbackoffモードで作動するために関連セグメント終点で受信機を構成すること」をSTATUSの現在の記述に読書して書きます。 ::= hdsl2ShdslEndpointMaintEntry3

hdsl2ShdslMaintSoftRestart OBJECT-TYPE
   SYNTAX      INTEGER
               {
               ready(1),
               restart(2)
               }
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object enables the manager to trigger a soft restart
      of the modem at the associated segment endpoint.  The manager
      may only set this object to the 'restart(2)' value, which
      initiates a restart.  The agent will perform a restart after
      approximately 5 seconds.  Following the 5 second period, the
      agent will restore the object to the 'ready(1)' state."
   ::= { hdsl2ShdslEndpointMaintEntry 4 }

hdsl2ShdslMaintSoftRestart OBJECT-TYPE SYNTAX INTEGERは(1)、再開(2)を準備します。マックス-ACCESSは「この物は、マネージャが関連セグメント終点でモデムの柔らかい再開の引き金となるのを可能にすること」をSTATUSの現在の記述に読書して書きます。 マネージャは'再開(2)'値にこの物を設定するだけであるかもしれません。(それは、再開を開始します)。 エージェントはおよそ5秒以降、再開を実行するでしょう。 「5第2ピリオドに続いて、エージェントは'持ち合わせの(1)'状態に物を復旧するでしょう。」 ::= hdsl2ShdslEndpointMaintEntry4

hdsl2ShdslUnitMaintTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslUnitMaintEntry

Hdsl2ShdslUnitMaintEntryのhdsl2ShdslUnitMaintTableオブジェクト・タイプ構文系列

Ray & Abbi                  Standards Track                    [Page 39]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[39ページ]。

   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table supports maintenance operations for units in a
      HDSL2/SHDSL line.  Entries in this table MUST be maintained
      in a persistent manner."
   ::= { hdsl2ShdslMibObjects 9 }

「HDSL2/SHDSLのユニットのためのこのテーブルサポート維持操作は裏打ちする」マックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 「しつこい方法でこのテーブルのエントリーを維持しなければなりません。」 ::= hdsl2ShdslMibObjects9

hdsl2ShdslUnitMaintEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslUnitMaintEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "An entry in the hdsl2ShdslUnitMaintTable.  Each entry
      corresponds to a single unit, and is indexed by the ifIndex
      of the HDSL2/SHDSL line and the UnitId of the associated
      unit."
   INDEX { ifIndex, hdsl2ShdslInvIndex  }
   ::= { hdsl2ShdslUnitMaintTable 1 }

hdsl2ShdslUnitMaintEntry OBJECT-TYPE SYNTAX Hdsl2ShdslUnitMaintEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「hdsl2ShdslUnitMaintTableのエントリー。」 「各エントリーは、単一の単位に対応している、HDSL2/SHDSL線のifIndexと関連ユニットのUnitIdによって索引をつけられます。」 ifIndex、hdsl2ShdslInvIndexに索引をつけてください:、:= hdsl2ShdslUnitMaintTable1

Hdsl2ShdslUnitMaintEntry ::=
   SEQUENCE
   {
   hdsl2ShdslMaintLoopbackTimeout     Integer32,
   hdsl2ShdslMaintUnitPowerSource     INTEGER
   }

Hdsl2ShdslUnitMaintEntry:、:= 系列hdsl2ShdslMaintLoopbackTimeout Integer32、hdsl2ShdslMaintUnitPowerSource整数

hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
   SYNTAX      Integer32(0..4095)
   UNITS       "minutes"
   MAX-ACCESS  read-write
   STATUS      current
   DESCRIPTION
     "This object configures the timeout value for loopbacks
      initiated at segments endpoints contained in the associated
      unit.  A value of 0 disables the timeout."
   ::= { hdsl2ShdslUnitMaintEntry 1 }

hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE SYNTAX Integer32(0 .4095)UNITS「数分」マックス-ACCESSは「この物は関連ユニットに含まれたセグメント終点で開始されたループバックのためにタイムアウト値を構成すること」をSTATUSの現在の記述に読書して書きます。 「0の値はタイムアウトを無能にします。」 ::= hdsl2ShdslUnitMaintEntry1

hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
   SYNTAX      INTEGER
               {
               local(1),
               span(2)
               }
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
     "This object indicates the DC power source being used by the

hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE SYNTAX INTEGER、地方の(1)、長さ(2)、マックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「この物が直流電源ソースのために使用されていた状態で存在を示す、」

Ray & Abbi                  Standards Track                    [Page 40]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[40ページ]。

      associated unit."
   ::= { hdsl2ShdslUnitMaintEntry 2 }

「関連ユニット。」 ::= hdsl2ShdslUnitMaintEntry2

-- Span Configuration Profile Group
--

-- 構成プロフィールグループにかかってください--

hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table supports definitions of span configuration
      profiles for SHDSL lines.  HDSL2 does not support these
      configuration options.  This table MUST be maintained
      in a persistent manner."
   ::= { hdsl2ShdslMibObjects 10 }

「長さ構成のこのテーブルサポート定義はSHDSL線に輪郭を描く」hdsl2ShdslSpanConfProfileTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 HDSL2はこれらの設定オプションをサポートしません。 「しつこい方法でこのテーブルを維持しなければなりません。」 ::= hdsl2ShdslMibObjects10

hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslSpanConfProfileEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "Each entry corresponds to a single span configuration
      profile.  Each profile contains a set of span configuration
      parameters.  The configuration parameters in a profile are
      applied to those lines referencing that profile (see the
      hdsl2ShdslSpanConfProfile object).  Profiles may be
      created/deleted using the row creation/deletion mechanism
      via hdsl2ShdslSpanConfProfileRowStatus.  If an active
      entry is referenced in hdsl2ShdslSpanConfProfile, the
      entry MUST remain active until all references are removed."
   INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
   ::= { hdsl2ShdslSpanConfProfileTable 1 }

hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE SYNTAX Hdsl2ShdslSpanConfProfileEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「各エントリーは単一の長さ構成プロフィールに対応しています」。 各プロフィールは1セットの長さ設定パラメータを含んでいます。 プロフィールの設定パラメータはそのプロフィールに参照をつけるそれらの線に適用されます(hdsl2ShdslSpanConfProfile物を見てください)。 プロフィールは、hdsl2ShdslSpanConfProfileRowStatusを通して列の創造/削除メカニズムを使用することで作成されるか、または削除されるかもしれません。 「活発なエントリーがhdsl2ShdslSpanConfProfileで参照をつけられるなら、すべての参照が取り除かれるまで、エントリーはアクティブなままでなければなりません。」 暗示しているhdsl2ShdslSpanConfProfileNameに索引をつけてください:、:= hdsl2ShdslSpanConfProfileTable1

Hdsl2ShdslSpanConfProfileEntry ::=
   SEQUENCE
   {
   hdsl2ShdslSpanConfProfileName               SnmpAdminString,
   hdsl2ShdslSpanConfWireInterface             INTEGER,
   hdsl2ShdslSpanConfMinLineRate               Unsigned32,
   hdsl2ShdslSpanConfMaxLineRate               Unsigned32,
   hdsl2ShdslSpanConfPSD                       INTEGER,
   hdsl2ShdslSpanConfTransmissionMode
                                   Hdsl2ShdslTransmissionModeType,
   hdsl2ShdslSpanConfRemoteEnabled             INTEGER,
   hdsl2ShdslSpanConfPowerFeeding              INTEGER,
   hdsl2ShdslSpanConfCurrCondTargetMarginDown  Integer32,
   hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,

Hdsl2ShdslSpanConfProfileEntry:、:= 系列、hdsl2ShdslSpanConfProfileName SnmpAdminString、hdsl2ShdslSpanConfWireInterface整数、hdsl2ShdslSpanConfMinLineRate Unsigned32、hdsl2ShdslSpanConfMaxLineRate Unsigned32、hdsl2ShdslSpanConfPSD整数、hdsl2ShdslSpanConfTransmissionMode Hdsl2ShdslTransmissionModeType、hdsl2ShdslSpanConfRemoteEnabled整数、hdsl2ShdslSpanConfPowerFeeding整数、hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32、hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32

Ray & Abbi                  Standards Track                    [Page 41]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[41ページ]。

   hdsl2ShdslSpanConfCurrCondTargetMarginUp    Integer32,
   hdsl2ShdslSpanConfWorstCaseTargetMarginUp   Integer32,
   hdsl2ShdslSpanConfUsedTargetMargins         BITS,
   hdsl2ShdslSpanConfReferenceClock
                                   Hdsl2ShdslClockReferenceType,
   hdsl2ShdslSpanConfLineProbeEnable           INTEGER,
   hdsl2ShdslSpanConfProfileRowStatus          RowStatus
   }

hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32、hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32、hdsl2ShdslSpanConfUsedTargetMarginsビット、hdsl2ShdslSpanConfReferenceClock Hdsl2ShdslClockReferenceType、hdsl2ShdslSpanConfLineProbeEnable整数、hdsl2ShdslSpanConfProfileRowStatus RowStatus

hdsl2ShdslSpanConfProfileName OBJECT-TYPE
   SYNTAX      SnmpAdminString (SIZE(1..32))
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This object is the unique index associated with this profile.
      Entries in this table are referenced via the object
      hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
   ::= { hdsl2ShdslSpanConfProfileEntry 1 }

hdsl2ShdslSpanConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1 .32))のマックス-ACCESSのアクセスしやすくないSTATUS現在の記述は「これが、反対するこのプロフィールに関連しているユニークなインデックスです」。 「このテーブルのエントリーはHdsl2ShdslSpanConfEntryの物のhdsl2ShdslSpanConfProfileを通して参照をつけられます。」 ::= hdsl2ShdslSpanConfProfileEntry1

hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
   SYNTAX      INTEGER
               {
               twoWire(1),
               fourWire(2)
               }
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the two-wire or optional four-wire
      operation for SHDSL Lines."
   DEFVAL      { twoWire }
   ::= { hdsl2ShdslSpanConfProfileEntry 2 }

マックス-ACCESSはSTATUSの現在の記述を読書して作成します。hdsl2ShdslSpanConfWireInterface OBJECT-TYPE SYNTAX INTEGER、twoWire(1)、fourWire(2)、「この物はSHDSL線のための2線式の、または、任意の4線式操作を構成します」。 DEFVAL twoWire:、:= hdsl2ShdslSpanConfProfileEntry2

hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
   SYNTAX      Unsigned32(0..4112000)
   UNITS       "bps"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the minimum transmission rate for
      the associated SHDSL Line in bits-per-second (bps).  If
      the minimum line rate equals the maximum line rate
      (hdsl2ShdslSpanMaxLineRate), the line rate is considered
      'fixed'.  If the minimum line rate is less than the maximum
      line rate, the line rate is considered 'rate-adaptive'."
   DEFVAL      { 1552000 }
   ::= { hdsl2ShdslSpanConfProfileEntry 3 }

マックス-ACCESSが読書して作成するhdsl2ShdslSpanConfMinLineRate OBJECT-TYPE SYNTAX Unsigned32(0 .4112000)UNITS「ビーピーエス」STATUSの現在の記述は「関連SHDSL線のためにbps(ビーピーエス)で最小の通信速度を構成これが反対するします」。 最小のライン料率が最大のライン料率(hdsl2ShdslSpanMaxLineRate)と等しいなら、ライン料率は'修理されている'と考えられます。 「最小のライン料率が最大のライン料率より少ないなら、ライン料率は'レート適応型である'と考えられます。」 DEFVAL1552000:、:= hdsl2ShdslSpanConfProfileEntry3

Ray & Abbi                  Standards Track                    [Page 42]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[42ページ]。

hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
   SYNTAX      Unsigned32(0..4112000)
   UNITS       "bps"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the maximum transmission rate for
      the associated SHDSL Line in bits-per-second (bps).  If
      the minimum line rate equals the maximum line rate
      (hdsl2ShdslSpanMaxLineRate), the line rate is considered
      'fixed'.  If the minimum line rate is less than the maximum
      line rate, the line rate is considered 'rate-adaptive'."
   DEFVAL      { 1552000 }
   ::= { hdsl2ShdslSpanConfProfileEntry 4 }

マックス-ACCESSが読書して作成するhdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE SYNTAX Unsigned32(0 .4112000)UNITS「ビーピーエス」STATUSの現在の記述は「関連SHDSL線のためにbps(ビーピーエス)で最大の通信速度を構成これが反対するします」。 最小のライン料率が最大のライン料率(hdsl2ShdslSpanMaxLineRate)と等しいなら、ライン料率は'修理されている'と考えられます。 「最小のライン料率が最大のライン料率より少ないなら、ライン料率は'レート適応型である'と考えられます。」 DEFVAL1552000:、:= hdsl2ShdslSpanConfProfileEntry4

hdsl2ShdslSpanConfPSD OBJECT-TYPE
   SYNTAX      INTEGER
               {
               symmetric(1),
               asymmetric(2)
               }
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures use of symmetric/asymmetric PSD (Power
      Spectral Density) Mask for the associated SHDSL Line.  Support
      for symmetric PSD is mandatory for all supported data rates.
      Support for asymmetric PSD is optional."
   DEFVAL      { symmetric }
   ::= { hdsl2ShdslSpanConfProfileEntry 5 }

マックス-ACCESSはSTATUSの現在の記述を読書して作成します。hdsl2ShdslSpanConfPSD OBJECT-TYPE SYNTAX INTEGER、左右対称の(1)、非対称の(2)、「この物は左右対称の、または、非対称のPSD(パワーSpectral Density)マスクの関連SHDSL線の使用を構成します」。 左右対称のPSDがすべてに義務的であるので、サポートはデータ信号速度を支持しました。 「非対称のPSDのサポートは任意です。」 DEFVAL、左右対称:、:= hdsl2ShdslSpanConfProfileEntry5

hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
   SYNTAX      Hdsl2ShdslTransmissionModeType
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object specifies the regional setting for the SHDSL
      line."
   DEFVAL      { { region1 } }
   ::= { hdsl2ShdslSpanConfProfileEntry 6 }

hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE SYNTAX Hdsl2ShdslTransmissionModeTypeマックス-ACCESSはSTATUSの現在の記述を読書して作成します。「この物はSHDSL線にセットしながら、地方を指定します」。 DEFVAL region1:、:= hdsl2ShdslSpanConfProfileEntry6

hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
   SYNTAX      INTEGER
               {
               enabled(1),
               disabled(2)
               }
   MAX-ACCESS  read-create

hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE SYNTAX INTEGERが(1)、身体障害者(2)を可能にした、マックス-ACCESSは読書して作成します。

Ray & Abbi                  Standards Track                    [Page 43]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[43ページ]。

   STATUS      current
   DESCRIPTION
     "This object enables/disables support for remote management
      of the units in a SHDSL line from the STU-R via the EOC."
   DEFVAL      { enabled }
   ::= { hdsl2ShdslSpanConfProfileEntry 7 }

STATUSの現在の記述は「EOCを通してSTU-RからSHDSL線でのユニットのリモート管理のサポートを可能にするか、または無効にこれが反対するします」。 DEFVALは可能にしました:、:= hdsl2ShdslSpanConfProfileEntry7

hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
   SYNTAX      INTEGER
               {
               noPower(1),
               powerFeed(2),
               wettingCurrent(3)
               }
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object enables/disables support for optional power
      feeding in a SHDSL line."
   DEFVAL      { noPower }
   ::= { hdsl2ShdslSpanConfProfileEntry 8 }

マックス-ACCESSはSTATUSの現在の記述を読書して作成します。hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE SYNTAX INTEGER、noPower(1)、powerFeed(2)、wettingCurrent(3)、「この物は、SHDSL線を入れながら、任意のパワーのサポートを可能にするか、または無効にします」。 DEFVAL noPower:、:= hdsl2ShdslSpanConfProfileEntry8

hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
   SYNTAX      Integer32(-10..21)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object specifies the downstream current condition target
      SNR margin for a SHDSL line.  The SNR margin is the difference
      between the desired SNR and the actual SNR.  Target SNR margin
      is the desired SNR margin for a unit."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslSpanConfProfileEntry 9 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE SYNTAX Integer32(-10 .21)のUNITSのSTATUSの現在の記述は「川下の現在の状態目標SNRマージンをSHDSL線に指定これが反対するします」。 SNRマージンは必要なSNRと実際のSNRの違いです。 「目標SNRマージンはユニット必要なSNRマージンです。」 DEFVAL0:、:= hdsl2ShdslSpanConfProfileEntry9

hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
   SYNTAX      Integer32(-10..21)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object specifies the downstream worst case target SNR
      margin for a SHDSL line.  The SNR margin is the difference
      between the desired SNR and the actual SNR.  Target SNR
      margin is the desired SNR margin for a unit."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslSpanConfProfileEntry 10 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE SYNTAX Integer32(-10 .21)のUNITSのSTATUSの現在の記述は「川下の最悪の場合目標SNRマージンをSHDSL線に指定これが反対するします」。 SNRマージンは必要なSNRと実際のSNRの違いです。 「目標SNRマージンはユニット必要なSNRマージンです。」 DEFVAL0:、:= hdsl2ShdslSpanConfProfileEntry10

Ray & Abbi                  Standards Track                    [Page 44]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[44ページ]。

hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
   SYNTAX      Integer32(-10..21)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object specifies the upstream current condition target
      SNR margin for a SHDSL line.  The SNR margin is the difference
      between the desired SNR and the actual SNR.  Target SNR margin
      is the desired SNR margin for a unit."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslSpanConfProfileEntry 11 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE SYNTAX Integer32(-10 .21)のUNITSのSTATUSの現在の記述は「上流の現在の状態目標SNRマージンをSHDSL線に指定これが反対するします」。 SNRマージンは必要なSNRと実際のSNRの違いです。 「目標SNRマージンはユニット必要なSNRマージンです。」 DEFVAL0:、:= hdsl2ShdslSpanConfProfileEntry11

hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
   SYNTAX      Integer32(-10..21)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object specifies the upstream worst case target SNR
      margin for a SHDSL line.  The SNR margin is the difference
      between the desired SNR and the actual SNR.  Target SNR margin
      is the desired SNR margin for a unit."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslSpanConfProfileEntry 12 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE SYNTAX Integer32(-10 .21)のUNITSのSTATUSの現在の記述は「上流の最悪の場合目標SNRマージンをSHDSL線に指定これが反対するします」。 SNRマージンは必要なSNRと実際のSNRの違いです。 「目標SNRマージンはユニット必要なSNRマージンです。」 DEFVAL0:、:= hdsl2ShdslSpanConfProfileEntry12

hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
   SYNTAX      BITS
               {
               currCondDown(0),
               worstCaseDown(1),
               currCondUp(2),
               worstCaseUp(3)
               }
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "Contains indicates whether a target SNR margin is enabled or
      disabled.  This is a bit-map of possible settings.  The
      various bit positions are:

hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE SYNTAX BITS、currCondDown(0)、worstCaseDown(1)、currCondUp(2)、worstCaseUp(3)、マックス-ACCESSは現在の記述が「目標SNRマージンが可能にされるかどうかを示すか、または無能にされて、含む」STATUSを読書して作成します。 これは可能な設定のしばらく地図です。 様々なビット位置は以下の通りです。

      currCondDown     current condition downstream target SNR
                       margin enabled

下流標的SNRマージンが可能にしたcurrCondDownの現在の状態

      worstCaseDown    worst case downstream target SNR margin
                       enabled

SNRマージンが可能にしたworstCaseDown最悪の場合下流標的

      currCondUp       current condition upstream target SNR

currCondUpの現在の状態上流目標SNR

Ray & Abbi                  Standards Track                    [Page 45]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[45ページ]。

                       margin enabled

可能にされたマージン

      worstCaseUp      worst case upstream target SNR margin
                       enabled."
   DEFVAL      { { currCondDown } }
   ::= { hdsl2ShdslSpanConfProfileEntry 13 }

「worstCaseUpは最もひどくSNRマージンが可能にした上流の目標をケースに入れます。」 DEFVAL currCondDown:、:= hdsl2ShdslSpanConfProfileEntry13

hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
   SYNTAX      Hdsl2ShdslClockReferenceType
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the clock reference for the STU-C
     in a SHDSL Line."
   DEFVAL      { localClk }
   ::= { hdsl2ShdslSpanConfProfileEntry 14 }

hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE SYNTAX Hdsl2ShdslClockReferenceTypeマックス-ACCESSはSTATUSの現在の記述を読書して作成します。「この物はSHDSL線のSTU-Cの時計参照を構成します」。 DEFVAL localClk:、:= hdsl2ShdslSpanConfProfileEntry14

hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
   SYNTAX      INTEGER
               {
               disable(1),
               enable(2)
               }
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object enables/disables support for Line Probe of
     the units in a SHDSL line.  When Line Probe is enabled, the
     system performs Line Probing to find the best possible
     rate.  If Line probe is disabled, the rate adaptation phase
     is skipped to shorten set up time."
   DEFVAL      { disable }
   ::= { hdsl2ShdslSpanConfProfileEntry 15 }

マックス-ACCESSはSTATUSの現在の記述を読書して作成します。hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE SYNTAX INTEGERが(1)を無能にして、(2)を可能にする、「この物は、SHDSL線でユニットの線Probeのサポートを可能にするか、または無効にします」。 線Probeが有効にされるとき、システムは、可能な限り良いレートを見つけるために線Probingを実行します。 「線徹底的調査は障害があるなら、レート適合フェーズは時間にセットを短くするためにスキップされます。」 DEFVALは以下を無能にします:= hdsl2ShdslSpanConfProfileEntry15

hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
   SYNTAX      RowStatus
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object controls creation/deletion of the associated
      entry in this table per the semantics of RowStatus.  If an
      active entry is referenced in hdsl2ShdslSpanConfProfile, the
      entry MUST remain active until all references are removed."
   ::= { hdsl2ShdslSpanConfProfileEntry 16 }

hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatusマックス-ACCESSは「この物はこのテーブルで関連エントリーについてRowStatusの意味論あたり創造/削除して制御する」STATUSの現在の記述を読書して作成します。 「活発なエントリーがhdsl2ShdslSpanConfProfileで参照をつけられるなら、すべての参照が取り除かれるまで、エントリーはアクティブなままでなければなりません。」 ::= hdsl2ShdslSpanConfProfileEntry16

-- Segment Endpoint Alarm Configuration Profile group
--

-- セグメントEndpoint Alarm Configuration Profileは分類します--

Ray & Abbi                  Standards Track                    [Page 46]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[46ページ]。

hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "This table supports definitions of alarm configuration
      profiles for HDSL2/SHDSL segment endpoints.  This table
      MUST be maintained in a persistent manner."
   ::= { hdsl2ShdslMibObjects 11 }

「アラーム構成のこのテーブルサポート定義はHDSL2/SHDSLセグメント終点に輪郭を描く」hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPEのSYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 「しつこい方法でこのテーブルを維持しなければなりません。」 ::= hdsl2ShdslMibObjects11

hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
   SYNTAX      Hdsl2ShdslEndpointAlarmConfProfileEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
     "Each entry corresponds to a single alarm configuration profile.
      Each profile contains a set of parameters for setting alarm
      thresholds for various performance attributes monitored at
      HDSL2/SHDSL segment endpoints.  Profiles may be created/deleted
      using the row creation/deletion mechanism via
      hdsl2ShdslEndpointAlarmConfProfileRowStatus.  If an active
      entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
      or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
      active until all references are removed."
   INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
   ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }

hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「各エントリーは単一のアラーム構成プロフィールに対応しています」。 各プロフィールはHDSL2/SHDSLセグメント終点でモニターされた様々な性能属性にアラーム敷居を設定するための1セットのパラメタを含んでいます。 プロフィールは、hdsl2ShdslEndpointAlarmConfProfileRowStatusを通して列の創造/削除メカニズムを使用することで作成されるか、または削除されるかもしれません。 「活発なエントリーがhdsl2ShdslSpanConfAlarmProfileかhdsl2ShdslEndpointAlarmConfProfileのどちらかで参照をつけられるなら、すべての参照が取り除かれるまで、エントリーはアクティブなままでなければなりません。」 暗示しているhdsl2ShdslEndpointAlarmConfProfileNameに索引をつけてください:、:= hdsl2ShdslEndpointAlarmConfProfileTable1

Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
   SEQUENCE
   {
   hdsl2ShdslEndpointAlarmConfProfileName       SnmpAdminString,
   hdsl2ShdslEndpointThreshLoopAttenuation      Integer32,
   hdsl2ShdslEndpointThreshSNRMargin            Integer32,
   hdsl2ShdslEndpointThreshES
               Hdsl2ShdslPerfIntervalThreshold,
   hdsl2ShdslEndpointThreshSES
               Hdsl2ShdslPerfIntervalThreshold,
   hdsl2ShdslEndpointThreshCRCanomalies         Integer32,
   hdsl2ShdslEndpointThreshLOSWS
               Hdsl2ShdslPerfIntervalThreshold,
   hdsl2ShdslEndpointThreshUAS
               Hdsl2ShdslPerfIntervalThreshold,
   hdsl2ShdslEndpointAlarmConfProfileRowStatus  RowStatus
   }

Hdsl2ShdslEndpointAlarmConfProfileEntry:、:= 系列hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString、hdsl2ShdslEndpointThreshLoopAttenuation Integer32、hdsl2ShdslEndpointThreshSNRMargin Integer32、hdsl2ShdslEndpointThreshES Hdsl2ShdslPerfIntervalThreshold、hdsl2ShdslEndpointThreshSES Hdsl2ShdslPerfIntervalThreshold、hdsl2ShdslEndpointThreshCRCanomalies Integer32、hdsl2ShdslEndpointThreshLOSWS Hdsl2ShdslPerfIntervalThreshold、hdsl2ShdslEndpointThreshUAS Hdsl2ShdslPerfIntervalThreshold、hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus

hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
   SYNTAX      SnmpAdminString (SIZE(1..32))
   MAX-ACCESS  not-accessible

アクセスしやすくないhdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1 .32))マックス-ACCESS

Ray & Abbi                  Standards Track                    [Page 47]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[47ページ]。

   STATUS      current
   DESCRIPTION
     "This object is the unique index associated with this profile."
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }

STATUSの現在の記述は「これが、反対するこのプロフィールに関連しているユニークなインデックスです」。 ::= hdsl2ShdslEndpointAlarmConfProfileEntry1

hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
   SYNTAX      Integer32(-127..128)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the loop attenuation alarm threshold.
      When the current value of hdsl2ShdslEndpointCurrAtn reaches
      or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
      MAY be generated."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE SYNTAX Integer32(-127 .128)のUNITSのSTATUSの現在の記述は「輪の減衰アラーム敷居を構成これが反対するします」。 「hdsl2ShdslEndpointCurrAtnの現行価値がこの敷居を達するか、または超えているとき、hdsl2ShdslLoopAttenCrossingは発生するかもしれません。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry2

hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
   SYNTAX      Integer32(-127..128)
   UNITS       "dB"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the SNR margin alarm threshold.
      When the current value of hdsl2ShdslEndpointCurrSnrMgn
      reaches or drops below this threshold, a
      hdsl2ShdslSNRMarginCrossing MAY be generated."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }

マックス-ACCESSが読書して作成する「dB」hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE SYNTAX Integer32(-127 .128)のUNITSのSTATUSの現在の記述は「SNRマージンアラーム敷居を構成これが反対するします」。 「hdsl2ShdslEndpointCurrSnrMgnの現行価値が達するか、またはこの敷居より下であるまで低下するとき、hdsl2ShdslSNRMarginCrossingは発生するかもしれません。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry3

hdsl2ShdslEndpointThreshES OBJECT-TYPE
   SYNTAX      Hdsl2ShdslPerfIntervalThreshold
   UNITS       "seconds"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the threshold for the number of
      errored seconds (ES) within any given 15-minute performance
      data collection interval.  If the value of errored seconds
      in a particular 15-minute collection interval reaches/
      exceeds this value, a hdsl2ShdslPerfESThresh MAY be
      generated.  At most one notification will be sent per
      interval per endpoint."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }

マックス-ACCESSが読書して作成するhdsl2ShdslEndpointThreshES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS「秒」STATUSの現在の記述は「どんな与えられた15分の性能データ収集間隔以内にもerrored秒(ES)の数のために敷居を構成これが反対するします」。 特定の15分の収集間隔のerrored秒の値がこの値を達するか、または超えているなら、hdsl2ShdslPerfESThreshは発生するかもしれません。 「最も1つでは、1終点あたりの間隔単位で通知を送るでしょう。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry4

hdsl2ShdslEndpointThreshSES OBJECT-TYPE

hdsl2ShdslEndpointThreshSESオブジェクト・タイプ

Ray & Abbi                  Standards Track                    [Page 48]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[48ページ]。

   SYNTAX      Hdsl2ShdslPerfIntervalThreshold
   UNITS       "seconds"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the threshold for the number of
      severely errored seconds (SES) within any given 15-minute
      performance data collection interval.  If the value of
      severely errored seconds in a particular 15-minute collection
      interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
      MAY be generated.  At most one notification will be sent per
      interval per endpoint."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }

マックス-ACCESSが読書して作成するSYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS「秒」STATUSの現在の記述は「どんな与えられた15分の性能データ収集間隔以内にも厳しくerroredされた秒(SES)の数のために敷居を構成これが反対するします」。 特定の15分の収集間隔の厳しくerroredされた秒の値がこの値を達するか、または超えているなら、hdsl2ShdslPerfSESThreshは発生するかもしれません。 「最も1つでは、1終点あたりの間隔単位で通知を送るでしょう。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry5

hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
   SYNTAX      Integer32
   UNITS       "detected CRC Anomalies"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the threshold for the number of
      CRC anomalies within any given 15-minute performance data
      collection interval.  If the value of CRC anomalies in a
      particular 15-minute collection interval reaches/exceeds
      this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
      generated.  At most one notification will be sent per
      interval per endpoint."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }

マックス-ACCESSが読書して作成する「検出されたCRC Anomalies」hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE SYNTAX Integer32 UNITSのSTATUSの現在の記述は「どんな与えられた15分の性能データ収集間隔以内にもCRC例外の数のために敷居を構成これが反対するします」。 特定の15分の収集間隔のCRC例外の値がこの値を達するか、または超えているなら、hdsl2ShdslPerfCRCanomaliesThreshは発生するかもしれません。 「最も1つでは、1終点あたりの間隔単位で通知を送るでしょう。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry6

hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
   SYNTAX      Hdsl2ShdslPerfIntervalThreshold
   UNITS       "seconds"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the threshold for the number of
      Loss of Sync Word (LOSW) Seconds within any given 15-minute
      performance data collection interval.  If the value of LOSW
      in a particular 15-minute collection interval reaches/exceeds
      this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
      At most one notification will be sent per interval per
      endpoint."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }

マックス-ACCESSが読書して作成するhdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS「秒」STATUSの現在の記述は「どんな与えられた15分の性能データ収集間隔以内にもSync Word(LOSW)秒のLossの数のために敷居を構成これが反対するします」。 特定の15分の収集間隔のLOSWの値がこの値を達するか、または超えているなら、hdsl2ShdslPerfLOSWSThreshは発生するかもしれません。 「最も1つでは、1終点あたりの間隔単位で通知を送るでしょう。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry7

hdsl2ShdslEndpointThreshUAS OBJECT-TYPE

hdsl2ShdslEndpointThreshUASオブジェクト・タイプ

Ray & Abbi                  Standards Track                    [Page 49]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[49ページ]。

   SYNTAX      Hdsl2ShdslPerfIntervalThreshold
   UNITS       "seconds"
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object configures the threshold for the number of
      unavailable seconds (UAS) within any given 15-minute
      performance data collection interval.  If the value of UAS
      in a particular 15-minute collection interval reaches/exceeds
      this value, a hdsl2ShdslPerfUASThresh MAY be generated.
      At most one notification will be sent per interval per
      endpoint."
   DEFVAL      { 0 }
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }

マックス-ACCESSが読書して作成するSYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS「秒」STATUSの現在の記述は「どんな与えられた15分の性能データ収集間隔以内にも入手できない秒(UAS)の数のために敷居を構成これが反対するします」。 特定の15分の収集間隔のUASの値がこの値を達するか、または超えているなら、hdsl2ShdslPerfUASThreshは発生するかもしれません。 「最も1つでは、1終点あたりの間隔単位で通知を送るでしょう。」 DEFVAL0:、:= hdsl2ShdslEndpointAlarmConfProfileEntry8

hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
   SYNTAX      RowStatus
   MAX-ACCESS  read-create
   STATUS      current
   DESCRIPTION
     "This object controls creation/deletion of the associated
      entry in this table as per the semantics of RowStatus.
      If an active entry is referenced in either
      hdsl2ShdslSpanConfAlarmProfile or
      hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
      active until all references are removed."
   ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }

マックス-ACCESSが読書して作成するhdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatusのSTATUSの現在の記述は「RowStatusの意味論に従ってこのテーブルでの関連エントリーの創造/削除を制御これが反対するします」。 「活発なエントリーがhdsl2ShdslSpanConfAlarmProfileかhdsl2ShdslEndpointAlarmConfProfileのどちらかで参照をつけられるなら、すべての参照が取り除かれるまで、エントリーはアクティブなままでなければなりません。」 ::= hdsl2ShdslEndpointAlarmConfProfileEntry9

-- Notifications Group
--

-- 通知は分類されます--

hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }

hdsl2ShdslNotifications物の識別子:、:= hdsl2ShdslMIB0

hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrAtn,
   hdsl2ShdslEndpointThreshLoopAttenuation
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the loop attenuation
      threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
      value) has been reached/exceeded for the HDSL2/SHDSL segment
      endpoint."
   ::= { hdsl2ShdslNotifications 1 }

hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE OBJECTS、hdsl2ShdslEndpointCurrAtn、hdsl2ShdslEndpointThreshLoopAttenuation、STATUSの現在の記述、「この通知は、輪の減衰敷居(hdsl2ShdslEndpointThreshLoopAttenuation値に従って)がHDSL2/SHDSLセグメント終点に達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications1

hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE

hdsl2ShdslSNRMarginCrossing通知タイプ

Ray & Abbi                  Standards Track                    [Page 50]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[50ページ]。

   OBJECTS
   {

   hdsl2ShdslEndpointCurrSnrMgn,
   hdsl2ShdslEndpointThreshSNRMargin
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the SNR margin threshold (as
      per the hdsl2ShdslEndpointThreshSNRMargin value) has been
      reached/exceeded for the HDSL2/SHDSL segment endpoint."
   ::= { hdsl2ShdslNotifications 2 }

hdsl2ShdslEndpointCurrSnrMgn、hdsl2ShdslEndpointThreshSNRMargin STATUSの現在の記述、「この通知は、SNRマージン敷居(hdsl2ShdslEndpointThreshSNRMargin値に従って)がHDSL2/SHDSLセグメント終点に達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications2

hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurr15MinES,
   hdsl2ShdslEndpointThreshES
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the errored seconds threshold
      (as per the hdsl2ShdslEndpointThreshES value) has been reached/
      exceeded for the HDSL2/SHDSL segment endpoint."
   ::= { hdsl2ShdslNotifications 3 }

hdsl2ShdslPerfESThresh NOTIFICATION-TYPE OBJECTS、hdsl2ShdslEndpointCurr15MinES、hdsl2ShdslEndpointThreshES、STATUSの現在の記述、「この通知は、errored秒敷居(hdsl2ShdslEndpointThreshES値に従って)がHDSL2/SHDSLセグメント終点に達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications3

hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurr15MinSES,
   hdsl2ShdslEndpointThreshSES
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the severely errored seconds
      threshold (as per the hdsl2ShdslEndpointThreshSES value) has
      been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
   ::= { hdsl2ShdslNotifications 4 }

hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE OBJECTS、hdsl2ShdslEndpointCurr15MinSES、hdsl2ShdslEndpointThreshSES、STATUSの現在の記述、「この通知は、厳しくerroredされた秒敷居(hdsl2ShdslEndpointThreshSES値に従って)がHDSL2/SHDSL Segment Endpointのために達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications4

hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurr15MinCRCanomalies,
   hdsl2ShdslEndpointThreshCRCanomalies
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the CRC anomalies threshold

hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE OBJECTS、hdsl2ShdslEndpointCurr15MinCRCanomalies、hdsl2ShdslEndpointThreshCRCanomalies、STATUSの現在の記述、「この通知がそれを示す、CRC例外敷居、」

Ray & Abbi                  Standards Track                    [Page 51]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[51ページ]。

      (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
      been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
   ::= { hdsl2ShdslNotifications 5 }

「HDSL2/SHDSL Segment Endpointのために達しているか、または超えられています(hdsl2ShdslEndpointThreshCRCanomalies値のように)。」 ::= hdsl2ShdslNotifications5

hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
   OBJECTS
   {

hdsl2ShdslPerfLOSWSThresh通知タイプは反対します。

   hdsl2ShdslEndpointCurr15MinLOSWS,
   hdsl2ShdslEndpointThreshLOSWS
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the LOSW seconds threshold
      (as per the hdsl2ShdslEndpointThreshLOSWS value) has been
      reached/exceeded for the HDSL2/SHDSL segment endpoint."
   ::= { hdsl2ShdslNotifications 6 }

hdsl2ShdslEndpointCurr15MinLOSWS、hdsl2ShdslEndpointThreshLOSWS STATUSの現在の記述、「この通知は、LOSW秒敷居(hdsl2ShdslEndpointThreshLOSWS値に従って)がHDSL2/SHDSLセグメント終点に達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications6

hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurr15MinUAS,
   hdsl2ShdslEndpointThreshUAS
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that the unavailable seconds
      threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
      been reached/exceeded for the HDSL2/SHDSL segment endpoint."
   ::= { hdsl2ShdslNotifications 7 }

hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE OBJECTS、hdsl2ShdslEndpointCurr15MinUAS、hdsl2ShdslEndpointThreshUAS、STATUSの現在の記述、「この通知は、入手できない秒敷居(hdsl2ShdslEndpointThreshUAS値に従って)がHDSL2/SHDSLセグメント終点に達しているか、または超えられているのを示します」。 ::= hdsl2ShdslNotifications7

hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslSpanConfNumRepeaters
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that a mismatch has been detected
      between the number of repeater/regenerator units configured
      for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
      object and the actual number of repeater/regenerator units
      discovered via the EOC."
   ::= { hdsl2ShdslNotifications 8 }

hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE OBJECTS hdsl2ShdslSpanConfNumRepeaters、STATUSの現在の記述、「この通知は、ミスマッチがhdsl2ShdslSpanConfNumRepeaters物を通してHDSL2/SHDSL線に構成されたリピータ/再生器ユニットの数とEOCを通して発見されたリピータ/再生器ユニットの実数の間に検出されたのを示します」。 ::= hdsl2ShdslNotifications8

hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
   OBJECTS
   {

hdsl2ShdslLoopbackFailure通知タイプは反対します。

Ray & Abbi                  Standards Track                    [Page 52]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[52ページ]。

   hdsl2ShdslMaintLoopbackConfig
   }
   STATUS     current
   DESCRIPTION
     "This notification indicates that an endpoint maintenance
      loopback command failed for an HDSL2/SHDSL segment."
   ::= { hdsl2ShdslNotifications 9 }

hdsl2ShdslMaintLoopbackConfig STATUSの現在の記述、「この通知は、終点維持ループバック命令がHDSL2/SHDSLセグメントのために失敗したのを示します」。 ::= hdsl2ShdslNotifications9

hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
      this endpoint has changed."
   ::= { hdsl2ShdslNotifications 10 }

hdsl2ShdslpowerBackoff NOTIFICATION-TYPE OBJECTS hdsl2ShdslEndpointCurrStatus、STATUSの現在の記述、「この通知は、powerBackoffのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications10

hdsl2ShdsldeviceFault NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      deviceFault in the hdsl2ShdslEndpointCurrStatus object for
      this endpoint has changed."
   ::= { hdsl2ShdslNotifications 11 }

hdsl2ShdsldeviceFault NOTIFICATION-TYPE OBJECTS hdsl2ShdslEndpointCurrStatus、STATUSの現在の記述、「この通知は、deviceFaultのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications11

hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
      for this endpoint has changed."
   ::= { hdsl2ShdslNotifications 12 }

hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE OBJECTS hdsl2ShdslEndpointCurrStatus、STATUSの現在の記述、「この通知は、dcContinuityFaultのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications12

hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus

hdsl2ShdslconfigInitFailure通知タイプが反対する、hdsl2ShdslEndpointCurrStatus

Ray & Abbi                  Standards Track                    [Page 53]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[53ページ]。

   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      configInitFailure in the hdsl2ShdslEndpointCurrStatus object
      for this endpoint has changed."
   ::= { hdsl2ShdslNotifications 13 }

} STATUSの現在の記述、「この通知は、configInitFailureのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications13

hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
      object for this endpoint has changed."
   ::= { hdsl2ShdslNotifications 14 }

hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE OBJECTS hdsl2ShdslEndpointCurrStatus、STATUSの現在の記述、「この通知は、protocolInitFailureのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications14

hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslEndpointCurrStatus
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates that the bit setting for
      noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
      for this endpoint has changed."
   ::= { hdsl2ShdslNotifications 15 }

hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE OBJECTS hdsl2ShdslEndpointCurrStatus、STATUSの現在の記述、「この通知は、noNeighborPresentのためにhdsl2ShdslEndpointCurrStatus物にこの終点にセットするビットが変化したのを示します」。 ::= hdsl2ShdslNotifications15

hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
   OBJECTS
   {
   hdsl2ShdslInvVendorID
   }
   STATUS    current
   DESCRIPTION
     "This notification indicates impending unit failure due to
      loss of local power (last gasp)."
   ::= { hdsl2ShdslNotifications 16 }

hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE OBJECTS hdsl2ShdslInvVendorID、「この通知は地方のパワー(最後に喘ぐ)の損失のためユニット失敗を迫らせながら、示す」STATUSの現在の記述。 ::= hdsl2ShdslNotifications16

-- conformance information
--

-- 順応情報--

hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups      OBJECT IDENTIFIER ::=

hdsl2ShdslConformance物の識別子:、:= hdsl2ShdslMIB3hdsl2ShdslGroups物の識別子:、:=

Ray & Abbi                  Standards Track                    [Page 54]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[54ページ]。

             { hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
             { hdsl2ShdslConformance 2 }

hdsl2ShdslConformance1hdsl2ShdslCompliances物の識別子:、:= hdsl2ShdslConformance2

-- agent compliance statements

-- エージェント承諾声明

hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
   STATUS  current
   DESCRIPTION
     "The section outlines compliance requirements for this MIB."
   MODULE
   MANDATORY-GROUPS
   {
   hdsl2ShdslSpanConfGroup,
   hdsl2ShdslSpanStatusGroup,
   hdsl2ShdslInventoryGroup,
   hdsl2ShdslEndpointConfGroup,
   hdsl2ShdslEndpointCurrGroup,
   hdsl2Shdsl15MinIntervalGroup,
   hdsl2Shdsl1DayIntervalGroup,
   hdsl2ShdslMaintenanceGroup,
   hdsl2ShdslEndpointAlarmConfGroup,
   hdsl2ShdslNotificationGroup
   }

hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE STATUSの現在の記述、「セクションはこのMIBのための承諾要件について概説します」。 モジュールの義務的なグループhdsl2ShdslSpanConfGroup、hdsl2ShdslSpanStatusGroup、hdsl2ShdslInventoryGroup、hdsl2ShdslEndpointConfGroup、hdsl2ShdslEndpointCurrGroup、hdsl2Shdsl15MinIntervalGroup、hdsl2Shdsl1DayIntervalGroup、hdsl2ShdslMaintenanceGroup、hdsl2ShdslEndpointAlarmConfGroup、hdsl2ShdslNotificationGroup

GROUP  hdsl2ShdslInventoryShdslGroup
   DESCRIPTION
     "Support for this group is only required for implementations
     supporting SHDSL lines."

GROUP hdsl2ShdslInventoryShdslGroup記述、「このグループのサポートがSHDSL線を支える実現に必要であるだけです」。

GROUP  hdsl2ShdslSpanShdslStatusGroup
   DESCRIPTION
     "Support for this group is only required for implementations
     supporting SHDSL lines."

GROUP hdsl2ShdslSpanShdslStatusGroup記述、「このグループのサポートがSHDSL線を支える実現に必要であるだけです」。

GROUP  hdsl2ShdslSpanConfProfileGroup
   DESCRIPTION
     "Support for this group is only required for implementations
     supporting SHDSL lines."

GROUP hdsl2ShdslSpanConfProfileGroup記述、「このグループのサポートがSHDSL線を支える実現に必要であるだけです」。

   ::= { hdsl2ShdslCompliances 1 }

::= hdsl2ShdslCompliances1

-- units of conformance
--

-- ユニットの順応--

hdsl2ShdslSpanConfGroup OBJECT-GROUP
   OBJECTS
   {

hdsl2ShdslSpanConfGroup物群対象

Ray & Abbi                  Standards Track                    [Page 55]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[55ページ]。

   hdsl2ShdslSpanConfNumRepeaters,
   hdsl2ShdslSpanConfProfile,
   hdsl2ShdslSpanConfAlarmProfile
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects for configuring span related
      parameters for HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 1 }

hdsl2ShdslSpanConfNumRepeaters、hdsl2ShdslSpanConfProfile、hdsl2ShdslSpanConfAlarmProfile 「長さがパラメタについて話したのを構成しながら、このグループはHDSL2/SHDSL線に物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups1

hdsl2ShdslSpanStatusGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslStatusNumAvailRepeaters
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects for retrieving span related
      status for HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 2 }

hdsl2ShdslSpanStatusGroup OBJECT-GROUP OBJECTS hdsl2ShdslStatusNumAvailRepeaters、「このグループは長さの関連する状態をHDSL2/SHDSL線に検索しながら、物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups2

hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslInvTransmissionModeCapability
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects for retrieving SHDSL-specific
      inventory information."
   ::= { hdsl2ShdslGroups 3 }

hdsl2ShdslInventoryShdslGroup OBJECT-GROUP OBJECTS hdsl2ShdslInvTransmissionModeCapability、「このグループはSHDSL特有の在庫情報を検索しながら、物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups3

hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslStatusMaxAttainableLineRate,
   hdsl2ShdslStatusActualLineRate,
   hdsl2ShdslStatusTransmissionModeCurrent
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects for retrieving SHDSL-specific
      span related status."
   ::= { hdsl2ShdslGroups 4 }

hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP OBJECTS、hdsl2ShdslStatusMaxAttainableLineRate、hdsl2ShdslStatusActualLineRate、hdsl2ShdslStatusTransmissionModeCurrent、「このグループはSHDSL-詳細の長さの関連する状態を検索しながら、物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups4

hdsl2ShdslInventoryGroup OBJECT-GROUP
   OBJECTS
   {

hdsl2ShdslInventoryGroup物群対象

Ray & Abbi                  Standards Track                    [Page 56]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[56ページ]。

   hdsl2ShdslInvVendorID,
   hdsl2ShdslInvVendorModelNumber,
   hdsl2ShdslInvVendorSerialNumber,
   hdsl2ShdslInvVendorEOCSoftwareVersion,
   hdsl2ShdslInvStandardVersion,
   hdsl2ShdslInvVendorListNumber,
   hdsl2ShdslInvVendorIssueNumber,
   hdsl2ShdslInvVendorSoftwareVersion,
   hdsl2ShdslInvEquipmentCode,
   hdsl2ShdslInvVendorOther
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects that provide unit inventory
      information about the units in HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 5 }

hdsl2ShdslInvVendorID、hdsl2ShdslInvVendorModelNumber、hdsl2ShdslInvVendorSerialNumber、hdsl2ShdslInvVendorEOCSoftwareVersion、hdsl2ShdslInvStandardVersion、hdsl2ShdslInvVendorListNumber、hdsl2ShdslInvVendorIssueNumber、hdsl2ShdslInvVendorSoftwareVersion、hdsl2ShdslInvEquipmentCode、hdsl2ShdslInvVendorOther STATUSの現在の記述、「このグループはユニットに関するユニット在庫情報をHDSL2/SHDSL線に供給する物を支えます」。 ::= hdsl2ShdslGroups5

hdsl2ShdslEndpointConfGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslEndpointCurrAtn
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects for configuring parameters for
      segment endpoints in HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 6 }

hdsl2ShdslEndpointConfGroup OBJECT-GROUP OBJECTS hdsl2ShdslEndpointCurrAtn、「このグループはHDSL2/SHDSL線のセグメント終点のためのパラメタを構成しながら、物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups6

hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslEndpointCurrAtn,
   hdsl2ShdslEndpointCurrSnrMgn,
   hdsl2ShdslEndpointCurrStatus,
   hdsl2ShdslEndpointES,
   hdsl2ShdslEndpointSES,
   hdsl2ShdslEndpointCRCanomalies,
   hdsl2ShdslEndpointLOSWS,
   hdsl2ShdslEndpointUAS,
   hdsl2ShdslEndpointCurr15MinTimeElapsed,
   hdsl2ShdslEndpointCurr15MinES,
   hdsl2ShdslEndpointCurr15MinSES,
   hdsl2ShdslEndpointCurr15MinCRCanomalies,
   hdsl2ShdslEndpointCurr15MinLOSWS,
   hdsl2ShdslEndpointCurr15MinUAS,
   hdsl2ShdslEndpointCurr1DayTimeElapsed,
   hdsl2ShdslEndpointCurr1DayES,
   hdsl2ShdslEndpointCurr1DaySES,

hdsl2ShdslEndpointCurrGroup物群対象、hdsl2ShdslEndpointCurrAtn、hdsl2ShdslEndpointCurrSnrMgn、hdsl2ShdslEndpointCurrStatus、hdsl2ShdslEndpointES、hdsl2ShdslEndpointSES、hdsl2ShdslEndpointCRCanomalies、hdsl2ShdslEndpointLOSWS、hdsl2ShdslEndpointUAS、hdsl2ShdslEndpointCurr15MinTimeElapsed; hdsl2ShdslEndpointCurr15MinES、hdsl2ShdslEndpointCurr15MinSES、hdsl2ShdslEndpointCurr15MinCRCanomalies、hdsl2ShdslEndpointCurr15MinLOSWS、hdsl2ShdslEndpointCurr15MinUAS、hdsl2ShdslEndpointCurr1DayTimeElapsed、hdsl2ShdslEndpointCurr1DayES、hdsl2ShdslEndpointCurr1DaySES

Ray & Abbi                  Standards Track                    [Page 57]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[57ページ]。

   hdsl2ShdslEndpointCurr1DayCRCanomalies,
   hdsl2ShdslEndpointCurr1DayLOSWS,
   hdsl2ShdslEndpointCurr1DayUAS
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects which provide current status and
      performance measurements relating to segment endpoints in
      HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 7 }

hdsl2ShdslEndpointCurr1DayCRCanomalies、hdsl2ShdslEndpointCurr1DayLOSWS、hdsl2ShdslEndpointCurr1DayUAS STATUSの現在の記述、「このグループは現在の状態を提供する物とHDSL2/SHDSL線でセグメント終点に関連する性能測定を支えます」。 ::= hdsl2ShdslGroups7

hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2Shdsl15MinIntervalES,
   hdsl2Shdsl15MinIntervalSES,
   hdsl2Shdsl15MinIntervalCRCanomalies,
   hdsl2Shdsl15MinIntervalLOSWS,
   hdsl2Shdsl15MinIntervalUAS
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects which maintain historic
      performance measurements relating to segment endpoints in
      HDSL2/SHDSL lines in 15-minute intervals."
   ::= { hdsl2ShdslGroups 8 }

hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP OBJECTS、hdsl2Shdsl15MinIntervalES、hdsl2Shdsl15MinIntervalSES、hdsl2Shdsl15MinIntervalCRCanomalies、hdsl2Shdsl15MinIntervalLOSWS、hdsl2Shdsl15MinIntervalUAS、STATUSの現在の記述、「このグループは15分の間隔でHDSL2/SHDSL線でセグメント終点に関連する歴史的な性能測定を維持する物を支えます」。 ::= hdsl2ShdslGroups8

hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2Shdsl1DayIntervalMoniSecs,
   hdsl2Shdsl1DayIntervalES,
   hdsl2Shdsl1DayIntervalSES,
   hdsl2Shdsl1DayIntervalCRCanomalies,
   hdsl2Shdsl1DayIntervalLOSWS,
   hdsl2Shdsl1DayIntervalUAS
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects which maintain historic
      performance measurements relating to segment endpoints in
      HDSL2/SHDSL lines in 1-day intervals."
   ::= { hdsl2ShdslGroups 9 }

hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP OBJECTS、hdsl2Shdsl1DayIntervalMoniSecs、hdsl2Shdsl1DayIntervalES、hdsl2Shdsl1DayIntervalSES、hdsl2Shdsl1DayIntervalCRCanomalies、hdsl2Shdsl1DayIntervalLOSWS、hdsl2Shdsl1DayIntervalUAS、STATUSの現在の記述、「このグループは1日間の間隔でHDSL2/SHDSL線でセグメント終点に関連する歴史的な性能測定を維持する物を支えます」。 ::= hdsl2ShdslGroups9

hdsl2ShdslMaintenanceGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslMaintLoopbackConfig,

hdsl2ShdslMaintenanceGroup物群対象、hdsl2ShdslMaintLoopbackConfig

Ray & Abbi                  Standards Track                    [Page 58]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[58ページ]。

   hdsl2ShdslMaintTipRingReversal,
   hdsl2ShdslMaintPowerBackOff,
   hdsl2ShdslMaintSoftRestart,
   hdsl2ShdslMaintLoopbackTimeout,
   hdsl2ShdslMaintUnitPowerSource
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects that provide support for
      maintenance actions for HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 10 }

hdsl2ShdslMaintTipRingReversal、hdsl2ShdslMaintPowerBackOff、hdsl2ShdslMaintSoftRestart、hdsl2ShdslMaintLoopbackTimeout、hdsl2ShdslMaintUnitPowerSource STATUSの現在の記述、「このグループはHDSL2/SHDSL線のための維持動作のサポートを提供する物を支えます」。 ::= hdsl2ShdslGroups10

hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslEndpointAlarmConfProfile,
   hdsl2ShdslEndpointThreshLoopAttenuation,
   hdsl2ShdslEndpointThreshSNRMargin,
   hdsl2ShdslEndpointThreshES,
   hdsl2ShdslEndpointThreshSES,
   hdsl2ShdslEndpointThreshCRCanomalies,
   hdsl2ShdslEndpointThreshLOSWS,
   hdsl2ShdslEndpointThreshUAS,
   hdsl2ShdslEndpointAlarmConfProfileRowStatus
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects that allow configuration of alarm
      thresholds for various performance parameters for HDSL2/SHDSL
      lines."
   ::= { hdsl2ShdslGroups 11 }

hdsl2ShdslEndpointAlarmConfGroup物群対象、hdsl2ShdslEndpointAlarmConfProfile、hdsl2ShdslEndpointThreshLoopAttenuation、hdsl2ShdslEndpointThreshSNRMargin、hdsl2ShdslEndpointThreshES、hdsl2ShdslEndpointThreshSES、hdsl2ShdslEndpointThreshCRCanomalies、hdsl2ShdslEndpointThreshLOSWS、hdsl2ShdslEndpointThreshUAS、hdsl2ShdslEndpointAlarmConfProfileRowStatus; STATUSの現在の記述、「このグループはHDSL2/SHDSL線のための様々な性能パラメタのためにアラーム敷居の構成を許す物を支えます」。 ::= hdsl2ShdslGroups11

hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
   NOTIFICATIONS
   {
   hdsl2ShdslLoopAttenCrossing,
   hdsl2ShdslSNRMarginCrossing,
   hdsl2ShdslPerfESThresh,
   hdsl2ShdslPerfSESThresh,
   hdsl2ShdslPerfCRCanomaliesThresh,
   hdsl2ShdslPerfLOSWSThresh,
   hdsl2ShdslPerfUASThresh,
   hdsl2ShdslSpanInvalidNumRepeaters,
   hdsl2ShdslLoopbackFailure,
   hdsl2ShdslpowerBackoff,
   hdsl2ShdsldeviceFault,
   hdsl2ShdsldcContinuityFault,
   hdsl2ShdslconfigInitFailure,

hdsl2ShdslNotificationGroup通知グループ通知、hdsl2ShdslLoopAttenCrossing、hdsl2ShdslSNRMarginCrossing、hdsl2ShdslPerfESThresh、hdsl2ShdslPerfSESThresh、hdsl2ShdslPerfCRCanomaliesThresh、hdsl2ShdslPerfLOSWSThresh、hdsl2ShdslPerfUASThresh、hdsl2ShdslSpanInvalidNumRepeaters、hdsl2ShdslLoopbackFailure、hdsl2ShdslpowerBackoff、hdsl2ShdsldeviceFault、hdsl2ShdsldcContinuityFault、hdsl2ShdslconfigInitFailure

Ray & Abbi                  Standards Track                    [Page 59]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[59ページ]。

   hdsl2ShdslprotocolInitFailure,
   hdsl2ShdslnoNeighborPresent,
   hdsl2ShdslLocalPowerLoss
   }
   STATUS      current
   DESCRIPTION
     "This group supports notifications of significant conditions
     associated with HDSL2/SHDSL lines."
   ::= { hdsl2ShdslGroups 12 }

hdsl2ShdslprotocolInitFailure、hdsl2ShdslnoNeighborPresent、hdsl2ShdslLocalPowerLoss 「重要な状態のこのグループの支持通知はHDSL2/SHDSL線に関連づけた」STATUSの現在の記述。 ::= hdsl2ShdslGroups12

hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
   OBJECTS
   {
   hdsl2ShdslSpanConfWireInterface,
   hdsl2ShdslSpanConfMinLineRate,
   hdsl2ShdslSpanConfMaxLineRate,
   hdsl2ShdslSpanConfPSD,
   hdsl2ShdslSpanConfTransmissionMode,
   hdsl2ShdslSpanConfRemoteEnabled,
   hdsl2ShdslSpanConfPowerFeeding,
   hdsl2ShdslSpanConfCurrCondTargetMarginDown,
   hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
   hdsl2ShdslSpanConfCurrCondTargetMarginUp,
   hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
   hdsl2ShdslSpanConfUsedTargetMargins,
   hdsl2ShdslSpanConfReferenceClock,
   hdsl2ShdslSpanConfLineProbeEnable,
   hdsl2ShdslSpanConfProfileRowStatus
   }
   STATUS      current
   DESCRIPTION
     "This group supports objects that constitute configuration
      profiles for configuring span related parameters in SHDSL
      lines."
   ::= { hdsl2ShdslGroups 13 }
END

hdsl2ShdslSpanConfProfileGroup物群対象; { hdsl2ShdslSpanConfWireInterface、hdsl2ShdslSpanConfMinLineRate、hdsl2ShdslSpanConfMaxLineRate、hdsl2ShdslSpanConfPSD、hdsl2ShdslSpanConfTransmissionMode、hdsl2ShdslSpanConfRemoteEnabled、hdsl2ShdslSpanConfPowerFeeding、hdsl2ShdslSpanConfCurrCondTargetMarginDown; hdsl2ShdslSpanConfWorstCaseTargetMarginDown、hdsl2ShdslSpanConfCurrCondTargetMarginUp、hdsl2ShdslSpanConfWorstCaseTargetMarginUp、hdsl2ShdslSpanConfUsedTargetMargins、hdsl2ShdslSpanConfReferenceClock、hdsl2ShdslSpanConfLineProbeEnable、hdsl2ShdslSpanConfProfileRowStatus; } 「SHDSL線で関係パラメータにかかるように構成しながら、このグループは構成プロフィールを構成する物を支える」STATUSの現在の記述。 ::= hdsl2ShdslGroups13は終わります。

7.  Security Considerations

7. セキュリティ問題

   Blocking unauthorized access to the HDSL2-SHDSL MIB via the element
   management system is outside the scope of this document.  It should
   be noted that access to the MIB permits the unauthorized entity to
   modify the profiles (section 6.4) such that both subscriber service
   and network operations can be interfered with.  Subscriber service
   can be altered by modifying any of a number of service
   characteristics such as rate partitioning and maximum transmission
   rates.  Network operations can be impacted by modification of
   notification thresholds such as SES thresholds.

このドキュメントの範囲の外に要素マネージメントシステムでHDSL2-SHDSL MIBへの不正アクセスを妨げるのがあります。 MIBへのアクセスが、加入者サービスとネットワーク操作の両方を妨げることができるように権限のない実体がプロフィール(セクション6.4)を変更することを許可することに注意されるべきです。 レート仕切りや最大の通信速度などの多くのサービスの特性のどれかを変更することによって、加入者サービスを変更できます。 SES敷居などの通知敷居の変更でネットワーク操作に影響を与えることができます。

Ray & Abbi                  Standards Track                    [Page 60]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[60ページ]。

   There are a number of managed objects in this MIB that may be
   considered to contain sensitive information.  Access to these objects
   would allow an intruder to obtain information about which vendor's
   equipment is in use on the network.  Further, such information is
   considered sensitive in many environments for competitive reasons.

多くの管理オブジェクトが機密情報を含むと考えられるかもしれないこのMIBにあります。 これらの物へのアクセスで、侵入者はどの業者の設備がネットワークで使用中であるかの情報を得ることができるでしょう。 さらに、そのような情報は競争力がある理由で、多くの環境で敏感であると考えられます。

   These identifying objects in the inventory group are:

目録グループで物を特定するこれらは以下の通りです。

   - hdsl2ShdslInvVendorID
   - hdsl2ShdslInvVendorModelNumber
   - hdsl2ShdslInvVendorSerialNumber
   - hdsl2ShdslInvVendorEOCSoftwareVersion
   - hdsl2ShdslInvStandardVersion
   - hdsl2ShdslInvVendorListNumber
   - hdsl2ShdslInvVendorIssueNumber
   - hdsl2ShdslInvVendorSoftwareVersion
   - hdsl2ShdslInvEquipmentCode
   - hdsl2ShdslInvVendorOther
   - hdsl2ShdslInvTransmissionModeCapability

- hdsl2ShdslInvVendorID--hdsl2ShdslInvVendorModelNumber--hdsl2ShdslInvVendorSerialNumber--hdsl2ShdslInvVendorEOCSoftwareVersion--hdsl2ShdslInvStandardVersion--hdsl2ShdslInvVendorListNumber--hdsl2ShdslInvVendorIssueNumber--hdsl2ShdslInvVendorSoftwareVersion--hdsl2ShdslInvEquipmentCode--hdsl2ShdslInvVendorOther--hdsl2ShdslInvTransmissionModeCapability

   Therefore, it may be important in some environments to control read
   access to these objects and possibly to even encrypt the values of
   these object when sending them over the network via SNMP.  Not all
   versions of SNMP provide features for such a secure environment.

したがって、SNMPを通してネットワークの上にそれらを送るとき、これらの物へのアクセスが読まれて、制御して、ことによると値をコード化するのさえいくつかの環境で、これらが反対するのは、重要であるかもしれません。 SNMPのすべてのバージョンがそのような安全な環境のための特徴を提供するというわけではありません。

   It is recommended that the implementors consider the security
   features as provided by the SNMPv3 framework.  Specifically, the use
   of the User-based Security Model RFC 2574 [12] and the View-based
   Access Control Model RFC 2575 [15] are recommended.

作成者がSNMPv3枠組みで提供するようにセキュリティ機能を考えるのは、お勧めです。 明確に、UserベースのSecurity Model RFC2574[12]とViewベースのAccess Control Model RFC2575[15]の使用はお勧めです。

   It is then the customer/user's responsibility to ensure that the SNMP
   entity giving access to an instance of this MIB, is properly
   configured to give access to those objects only to those principals
   (users) that have legitimate rights to access them.

そして、それらにアクセスする正当な権利を持っているそれらの校長だけ(ユーザ)にそれらの物へのアクセスを与えるために構成されて、それはこのMIBの例へのアクセスを与えるSNMP実体が適切にそうであることを保証する顧客/ユーザの責任です。

   HDSL2-SHDSL layer connectivity from the xtuR will permit the
   subscriber to manipulate both the HDSL2-SHDSL link directly and the
   HDSL2-SHDSL embedded  operations channel (EOC) for their own loop.
   For example, unchecked or unfiltered fluctuations initiated by the
   subscriber could generate sufficient notifications to potentially
   overwhelm either the management interface to the network or the
   element manager.

xtuRからのHDSL2-SHDSL層の接続性は、加入者がそれら自身の輪のために、HDSL2-SHDSLが直接リンクする両方とHDSL2-SHDSLの埋め込まれた操作チャンネル(EOC)を操作することを許可するでしょう。 例えば、加入者によって起こされた抑制されないか非濾過の変動は潜在的にネットワークへの管理インタフェースか要素マネージャのどちらかを圧倒できるくらいの通知を発生させるかもしれません。

   It should be noted that interface indices in this MIB are maintained
   persistently.  VACM data relating to these should be stored
   persistently.

このMIBのインタフェースインデックスリストが持続して維持されることに注意されるべきです。 これらに関連するVACMデータは持続して格納されるべきです。

Ray & Abbi                  Standards Track                    [Page 61]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[61ページ]。

   There are a number of management objects defined in this MIB that
   have a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.

aがあります。読書して書くことのマックス-ACCESS節を持っているこのMIBで定義された管理物に付番する、そして/または、読書して作成します。 そのような物はいくつかのネットワーク環境で敏感であるか、または傷つきやすいと考えられるかもしれません。 適切な保護のない非安全な環境におけるSET操作のサポートはネットワーク操作のときにマイナスの影響がある場合があります。

8.  Acknowledgments

8. 承認

   The authors are deeply grateful to the authors of the ADSL LINE MIB
   (RFC 2662 [23]), Gregory Bathrick and Faye Ly, as much of the text
   and structure of this document originates in their documents.

作者は深くADSL LINE MIBの作者に感謝しています。(テキストの多く、このドキュメントの構造としてのRFC2662[23])、グレゴリーBathrick、およびフェイLyは彼らのドキュメントで起こります。

   The authors are also grateful to the authors of FR MFR MIB (RFC 3020
   [24]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the majority
   of the Security Considerations section was lifted from their
   document.

また、作者もFR MFR MIBの作者に感謝しています。(Security Considerations部の大部分としてのRFC3020[24])、Prayson Pate、ボブ・リンチ、およびケネスRehbehnは彼らのドキュメントから剽窃されました。

   The authors also acknowledge the importance of the contributions and
   suggestions regarding interface indexing structures received from
   David Horton of CITR.

また、作者は構造がCITRのデヴィッドホートンから受けたインタフェースインデックスに関する貢献と提案の重要性を承認します。

   Other contributions were received from the following:

以下から他の貢献を受けました:

      Philip Bergstresser (Adtran)
      Steve Blackwell (Centillium)
      Umberto Bonollo (NEC Australia)
      Yagal Hachmon (RAD)
      Mark Johnson (Red Point)
      Sharon Mantin (Orckit)
      Moti Morgenstern (ECI)
      Raymond Murphy (Ericsson)
      Lee Nipper (Verilink)
      Randy Presuhn (BMC Software)
      Katy Sherman (Orckit)
      Mike Sneed (ECI)
      Jon Turney (DSL Solutions)
      Aron Wahl (Memotec)
      Bert Wijnen (Lucent)
      Michael Wrobel (Memotec)

フィリップBergstresser(Adtran)スティーブ・ブラックウェル(Centillium)ウンベルトBonollo(NECオーストラリア)Yagal Hachmon(rad)マーク・ジョンソン(赤いポイント)シャロンMantin(Orckit)モティ・モーガンスターン(ECI)・レイモンド・マーフィー(エリクソン)・リー・ニッパー(Verilink)ランディPresuhn(BMCソフトウェア)ケイティ・シャーマン(Orckit)マイクSneed(ECI)ジョン・ターネイ(DSLソリューション)・アロン・ウォール(Memotec)バートWijnen(透明な)マイケル・ローベル(Memotec)

Ray & Abbi                  Standards Track                    [Page 62]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[62ページ]。

9.  References

9. 参照

   [1]   Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for
         Describing SNMP Management Frameworks", RFC 2571, April 1999.

[1] ハリントンとD.とPresuhnとR.とB.Wijnen、「SNMP管理枠組みについて説明するための構造」、RFC2571、1999年4月。

   [2]   Rose, M. and K. McCloghrie, "Structure and Identification of
         Management Information for TCP/IP-based Internets", STD 16, RFC
         1155, May 1990.

[2] ローズ、M.、およびK.McCloghrie、「TCP/IPベースのインターネットのための経営情報の構造と識別」(STD16、RFC1155)は1990がそうするかもしれません。

   [3]   Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,
         RFC 1212, March 1991.

[3] ローズとM.とK.McCloghrie、「簡潔なMIB定義」、STD16、RFC1212、1991年3月。

   [4]   Rose, M., "A Convention for Defining Traps for use with the
         SNMP", RFC 1215, March 1991.

[4] ローズ、1991年3月、M.、「SNMPとの使用のためのDefining TrapsのためのConvention」RFC1215。

   [5]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
         M. and S. Waldbusser, "Structure of Management Information
         Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

[5]McCloghrie、K.、パーキンス、D.、Schoenwaelder、J.、ケース、J.、ローズ、M.、およびS.Waldbusser、「経営情報バージョン2(SMIv2)の構造」、STD58、RFC2578(1999年4月)。

   [6]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
         M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58,
         RFC 2579, April 1999.

[6]McCloghrie、K.、パーキンス、D.、Schoenwaelder、J.、ケース、J.、ローズ、M.、およびS.Waldbusser、「SMIv2"、STD58、RFC2579、1999年4月の原文のコンベンション。」

   [7]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
         M. and S. Waldbusser, "Conformance Statements for SMIv2", STD
         58, RFC 2580, April 1999.

[7]McCloghrie、K.、パーキンス、D.、Schoenwaelder、J.、ケース、J.、ローズ、M.、およびS.Waldbusser、「SMIv2"、STD58、RFC2580、1999年4月のための順応声明。」

   [8]   Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
         Network Management Protocol", STD 15, RFC 1157, May 1990.

[8] ケース、J.、ヒョードル、M.、Schoffstall、M.、およびJ.デーヴィン(「簡単なネットワーク管理プロトコル」、STD15、RFC1157)は1990がそうするかもしれません。

   [9]   Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
         "Introduction to Community-based SNMPv2", RFC 1901, January
         1996.

[9]ケース、J.、McCloghrie、K.、ローズ、M.、およびS.Waldbusser、「地域密着型のSNMPv2"への紹介、RFC1901、1996年1月。」

   [10]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
         "Transport Mappings for Version 2 of the Simple Network
         Management Protocol (SNMPv2)", RFC 1906, January 1996.

[10]ケース、J.、McCloghrie、K.、ローズ、M.、およびS.Waldbusser、「簡単なネットワークマネージメントのバージョン2のための輸送マッピングは(SNMPv2)について議定書の中で述べます」、RFC1906、1996年1月。

   [11]  Case, J., Harrington D., Presuhn, R. and B. Wijnen, "Message
         Processing and Dispatching for the Simple Network Management
         Protocol (SNMP)", RFC 2572, April 1999.

[11]ケース、J.、ハリントンD.、Presuhn、R.、およびB.Wijnen、「メッセージ処理と簡単なネットワークマネージメントのために急いでいるのは(SNMP)について議定書の中で述べます」、RFC2572、1999年4月。

   [12]  Blumenthal, U. and B. Wijnen, "User-based Security Model (USM)
         for version 3 of the Simple Network Management Protocol
         (SNMPv3)", RFC 2574, April 1999.

[12] ブルーメンソルとU.とB.Wijnen、「Simple Network Managementプロトコル(SNMPv3)のバージョン3のためのユーザベースのSecurity Model(USM)」、RFC2574、1999年4月。

Ray & Abbi                  Standards Track                    [Page 63]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[63ページ]。

   [13]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol
         Operations for Version 2 of the Simple Network Management
         Protocol (SNMPv2)", RFC 1905, January 1996.

[13] ケース、J.、McCloghrie(K.、ローズ、M.、およびS.Waldbusser)は「簡単なネットワーク管理プロトコル(SNMPv2)のバージョン2のための操作について議定書の中で述べます」、RFC1905、1996年1月。

   [14]  Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC
         2573, April 1999.

[14] レビとD.とマイヤーとP.とB.スチュワート、「SNMPv3アプリケーション」、RFC2573、1999年4月。

   [15]  Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access
         Control Model (VACM) for the Simple Network Management Protocol
         (SNMP)", RFC 2575, April 1999.

[15] Wijnen、B.、Presuhn、R.、およびK.McCloghrie、「簡単なネットワークマネージメントのための視点ベースのアクセス管理モデル(VACM)は(SNMP)について議定書の中で述べます」、RFC2575、1999年4月。

   [16]  Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction
         to Version 3 of the Internet-standard Network Management
         Framework", RFC 2570, April 1999.

[16] ケースとJ.とマンディとR.、パーテインとD.とB.スチュワート、「インターネット標準ネットワークマネージメント枠組みのバージョン3への序論」RFC2570(1999年4月)。

   [17]  Bradner, S., "Key Words for use in RFCs to Indicate Requirement
         Levels", BCP 14, RFC 2119, March 1997.

[17] ブラドナー、S.、「Indicate Requirement LevelsへのRFCsにおける使用のための主要なワーズ」、BCP14、RFC2119、1997年3月。

   [18]  American National Standards Institute, ANSI T1E1.4/2000-006,
         February 2000.

[18]American National Standards Institut、ANSI T1E1.4/2000-006、2000年2月。

   [19]  Blackwell, S., Editor, "Single-Pair High-Speed Digital
         Subscriber Line (SHDSL) Transceivers", ITU-T Draft G.991.2,
         April 2000.

[19] ブラックウェル、S.、エディタ、「単独の組の高速デジタル加入者線(SHDSL)トランシーバー」、ITU-TはG.991.2、2000年4月を作成します。

   [20]  McCloghrie, K. and M. Rose, M., "Management Information Base
         for Network Management of TCP/IP-based internets: MIB-II", STD
         17, RFC 1213, March 1991.

[20]McCloghrie、K.とM.ローズ、M.、「TCP/IPベースのインターネットのNetwork Managementのための管理Information基地:」 「MIB-II」、STD17、RFC1213、1991年3月。

   [21]  McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB",
         RFC 2863, June 2000.

[21]McCloghrieとK.とF.Kastenholz、「インタフェースはMIBを分類する」RFC2863、2000年6月。

   [22]  Tesink, K., "Textual Conventions for MIB Modules Using
         Performance History Based on 15 Minute Intervals", RFC 2493,
         January 1999.

[22]Tesink、K.、「MIBモジュールのための15分の間隔に基づくパフォーマンス歴史を使用する原文のコンベンション」、RFC2493、1999年1月。

   [23]  Bathrick, G. and F. Ly, "Definitions of Managed Objects for the
         ADSL Lines", RFC 2662, August 1999.

[23]BathrickとG.とF.Ly、「ADSL線のための管理オブジェクトの定義」、RFC2662、1999年8月。

   [24]  Pate, P., Lynch, B. and K. Rehbehn, "Definitions of Managed
         Objects for Monitoring and Controlling the UNI/NNI Multilink
         Frame Relay Function", RFC 3020, December 2000.

[24]頭、P.、リンチ、B.、およびK.Rehbehn、「UNI/NNIマルチリンクフレームリレーをモニターして、制御するための管理オブジェクトの定義は機能します」、RFC3020、2000年12月。

   [25]  American National Standards Institute, "Coded Identification of
         Equipment Entities of the North American Telecommunications
         System for the Purpose of Information Exchange", T1.213-2001.

[25]American National Standards Institut、「情報交換の目的のための北米の情報通信システムの設備実体のコード化された識別。」(T1.213-2001)

Ray & Abbi                  Standards Track                    [Page 64]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[64ページ]。

10.  Intellectual Property Notice

10. 知的所有権通知

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

IETFはどんな知的所有権の正当性か範囲、実現に関係すると主張されるかもしれない他の権利、本書では説明された技術の使用またはそのような権利の下におけるどんなライセンスも利用可能であるかもしれない、または利用可能でないかもしれない範囲に関しても立場を全く取りません。 どちらも、それはそれを表しません。いずれもどんなそのような権利も特定するための努力にしました。 BCP-11で標準化過程の権利と規格関連のドキュメンテーションに関するIETFの手順に関する情報を見つけることができます。 権利のクレームのコピーで利用可能に作られるべきライセンスの保証、または一般的なライセンスか許可が作成者によるそのような所有権の使用に得させられた試みの結果が公表といずれにも利用可能になったか、またはIETF事務局からこの仕様のユーザを得ることができます。

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

IETFはこの規格を練習するのに必要であるかもしれない技術をカバーするかもしれないどんな著作権もその注目していただくどんな利害関係者、特許、特許出願、または他の所有権も招待します。 IETF専務に情報を記述してください。

11.  Authors' Addresses

11. 作者のアドレス

   Bob Ray
   PESA Switching Systems, Inc.
   330-A Wynn Drive
   Huntsville, AL 35805 USA

ボブ・レイ・ペサSwitching Systems Inc.330-Aウィン・Drive AL35805ハンツビル(米国)

   Phone: +1 256 726 9200 ext. 142
   Fax: +1 256 726 9271
   EMail: rray@pesa.com

以下に電話をしてください。 +1 9200がextする256 726。 142 Fax: +1 9271年の256 726メール: rray@pesa.com

   Rajesh Abbi
   Alcatel USA
   2912 Wake Forest Road
   Raleigh, NC 27609-7860 USA

ラジェッシュAbbiアルカテル米国2912ウェイクフォーレストのRoad NC27609-7860ローリー(米国)

   Phone: +1 919-850-6194
   Fax:   +1 919-850-6670
   EMail: Rajesh.Abbi@alcatel.com

以下に電話をしてください。 +1 919-850-6194Fax: +1 919-850-6670 メールしてください: Rajesh.Abbi@alcatel.com

Ray & Abbi                  Standards Track                    [Page 65]

RFC 3276                  HDSL2-SHDSL-LINE MIB                  May 2002

レイとAbbi規格はHDSL2-SHDSL-線MIB2002年5月にRFC3276を追跡します[65ページ]。

12.  Full Copyright Statement

12. 完全な著作権宣言文

   Copyright (C) The Internet Society (2002).  All Rights Reserved.

Copyright(C)インターネット協会(2002)。 All rights reserved。

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

それに関するこのドキュメントと翻訳は、コピーして、それが批評するか、またはそうでなければわかる他のもの、および派生している作品に提供するか、または準備されているかもしれなくて、コピーされて、発行されて、全体か一部広げられた実現を助けるかもしれません、どんな種類の制限なしでも、上の版権情報とこのパラグラフがそのようなすべてのコピーと派生している作品の上に含まれていれば。 しかしながら、このドキュメント自体は何らかの方法で変更されないかもしれません、インターネット協会か他のインターネット組織の版権情報か参照を取り除くのなどように、それを英語以外の言語に翻訳するのが著作権のための手順がインターネットStandardsの過程で定義したどのケースに従わなければならないか、必要に応じてさもなければ、インターネット標準を開発する目的に必要であるのを除いて。

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

上に承諾された限られた許容は、永久であり、インターネット協会、後継者または案配によって取り消されないでしょう。

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

このドキュメントとそして、「そのままで」という基礎とインターネットの振興発展を目的とする組織に、インターネット・エンジニアリング・タスク・フォースが速達の、または、暗示しているすべての保証を放棄するかどうかというここにことであり、他を含んでいて、含まれて、情報の使用がここに侵害しないどんな保証も少しもまっすぐになるという情報か市場性か特定目的への適合性のどんな黙示的な保証。

Acknowledgement

承認

   Funding for the RFC Editor function is currently provided by the
   Internet Society.

RFC Editor機能のための基金は現在、インターネット協会によって提供されます。

Ray & Abbi                  Standards Track                    [Page 66]

レイとAbbi標準化過程[66ページ]

一覧

 RFC 1〜100  RFC 1401〜1500  RFC 2801〜2900  RFC 4201〜4300 
 RFC 101〜200  RFC 1501〜1600  RFC 2901〜3000  RFC 4301〜4400 
 RFC 201〜300  RFC 1601〜1700  RFC 3001〜3100  RFC 4401〜4500 
 RFC 301〜400  RFC 1701〜1800  RFC 3101〜3200  RFC 4501〜4600 
 RFC 401〜500  RFC 1801〜1900  RFC 3201〜3300  RFC 4601〜4700 
 RFC 501〜600  RFC 1901〜2000  RFC 3301〜3400  RFC 4701〜4800 
 RFC 601〜700  RFC 2001〜2100  RFC 3401〜3500  RFC 4801〜4900 
 RFC 701〜800  RFC 2101〜2200  RFC 3501〜3600  RFC 4901〜5000 
 RFC 801〜900  RFC 2201〜2300  RFC 3601〜3700  RFC 5001〜5100 
 RFC 901〜1000  RFC 2301〜2400  RFC 3701〜3800  RFC 5101〜5200 
 RFC 1001〜1100  RFC 2401〜2500  RFC 3801〜3900  RFC 5201〜5300 
 RFC 1101〜1200  RFC 2501〜2600  RFC 3901〜4000  RFC 5301〜5400 
 RFC 1201〜1300  RFC 2601〜2700  RFC 4001〜4100  RFC 5401〜5500 
 RFC 1301〜1400  RFC 2701〜2800  RFC 4101〜4200 

スポンサーリンク

「ID」や「ID_xxxx」という文字列があるCSVファイルをExcelで開くとSYLKエラーが出る

ホームページ製作・web系アプリ系の製作案件募集中です。

上に戻る